Quick Parts Search
Quick Parts Search
Need Some Help?







How do you Change, Replace, or Install 1992-1996 Toyota Camry Outside Door Handle Replacement





Tools required:
  • Flathead screwdriver

  • Phillips screwdriver

  • 10mm socket/ratchet with extension


Step 1: Remove the panel covering the side mirror mount.

Use your flathead screwdriver.

Step 2: Using the flathead screwdriver, pry and remove the plastic door handle casing.

Step 3: Remove the 4 screw covers with the flathead screwdriver.


These covers are located on the interior of the door panel. Two will be near the door hinge, one just above the window control panel, and one just below the door-mounted arm rest.

Step 5: Remove the 5 retaining screws that help to hold the door panel in place.

Step 6: Locate and depress the two retaining pins that are at the end of the door panel.


To remove these pins, use the screwdriver to depress the center of the pins, and then pry them loose.

Step 7: Remove the 4 retaining pins along the bottom of the interior door panel.

Step 8: You can now remove the door panel.

Step 9: Disconnect the window control panel's electrical harness.

Step 10: Remove the small circular cover in the upper corner of the door frame.

Step 11: Locate the 10mm bolts that hold the door handle in place and remove them.

Step 12: Release the yellow clip that is inside the door frame.


This clip is located just on the inside of the exterior door handle.

Step 13: You can now pull the exterior door handle from the door.

As you are pulling the door handle out, you will need to disconnect one more clip.

Step 14: Using the 10mm socket, remove the lock from the old handle and attach to your new one.

Step 15: Slide the new handle into the door.


Attach the clip to push the door handle into place.

Step 16: Using the 10mm socket, replace the retaining bolts to secure the new door handle into place.

You are now working from the INTERIOR of the door.

Step 17: Reattach the rod and clip on the interior of the door frame.

These components are found just inside the door handle.

NOTE: The water shield is the plastic sheet that lies beneath the door panel. Be careful not to tear it. When reattaching it, if the sticky adhesive has lost its touch, you can use tape to reattach it!

Step 18: Replace the door panel.

Replace all clips and screws to secure the door panel.

Step 19: Reconnect the electrical harness for the window control panel (and speaker, if necessary), and reattach the panel and door handle casing.




Please Note

While we are more than happy to create these installation guides for your benefit, we cannot maintain any liability regarding the part, or the driving experience, once the part has been replaced/installed. We always guarantee the quality of the parts we provide, but the installation liability rests solely on the installer.

And, though we are always here to answer your questions, please note that our technicians created these guides for your convenience, and cannot provide assistance beyond this guide.


If you're looking for a good deal on the parts mentioned in this instructional guide, be sure to check these out:


These Part Change / Installation Instructions Apply to
96 1996, 95 1995, 94 1994, 93 1993, 92 1992 Toyota Camry Outside Door Handle Replacement Instructions
- POPULAR GUIDES: TOYOTA CAMRY -

Toyota Camry Crankshaft Sensor Replacement

2002-2006 Toyota Camry Headlight

2002-2006 Toyota Camry Side Mirror Replacement

2002-2006 Toyota Camry Tail Light Replacement

1997-2001 Toyota Camry Corner Light Replacement

1997-2001 Toyota Camry Headlight Replacement

1995-1996 Toyota Camry Headlight Replacement

1992-1996 Toyota Camry Side Mirror Replacement

1992-1994 Toyota Camry Headlight Replacement


Your cart is completely and totally empty!

USERNAME (Your E-Mail)

PASSWORD
Sign UpForgot Password

Enter email address here:
  


Payment Methods Accepted