Quick Parts Search
Quick Parts Search
Need Some Help?

Go-parts Reviews - SiteJabber



How do you Change, Replace, or Install Broken 2000-2005 Buick LeSabre Power Window Motor Replacement

Fits Years: 2000, 2001, 2002, 2003, 2004, 2005


Tools required:

  • Phillips screwdriver (short and regular)

  • Flathead screwdriver

  • Door Panel Clip Tool (or putty knife)


Step 1: Open the vehicle's door.

Step 2: Using the flathead screwdriver, pry and remove the trim panel near the side mirror's mounting area.

Step 3: Disconnect the wiring harness (1) from the back of this trim panel.

Step 4: Pry and remove the interior door handle's bezel. Disconnect the wiring harness (1) from the back of the bezel.

Step 5: Pry and remove the reflector from the interior door panel.

Step 6: Loosen and remove the Phillips screw (1) behind the reflector's mounting point.

Step 7: Loosen and remove the Phillips screw (1) inside the interior door handle.

Step 8: Using the door panel clip tool (or putty knife), pry and separate the interior door panel from the door frame. You will hear the retaining pins "pop" as they disengage, releasing the panel.

Step 9: Disconnect the wiring harness (1) from the back of the interior door panel.

Step 10: You can now completely remove the interior door panel.

Step 11: GENTLY peel back the water shield. Be sure not to tear it, as we'll need it later!


You don't need to completely remove the shield. Instead, just peel it back enough to expose the window motor.

Step 12: Disconnect the window motor's wiring harness (1).

Step 13: Loosen and remove the Phillips screws (3) that hold the motor to the assembly.


NOTE: You will need to use the SHORT Phillips screwdriver, as the screw heads are on the BACK of the assembly.

Step 14: You can now remove the power window motor from the vehicle.

Step 15: Mount the new power window motor by tightening the Phillips screws (3). Connect the window motor's wiring harness (1).

Step 16: Reattach the water shield.

Step 17: To reattach the interior door panel, connect the wiring harness (1), and mount it to the door frame by re-engaging the retaining pins.


NOTE: Be sure to slide the edge of the interior door panel onto the groove that holds the panel in place. This will make sense once you see the back of the panel!

Step 18: With a firm "strike" (but not too firm!) near each retaining pin, you can snap all of the retaining pins back into place.

Step 19: Tighten the Phillips screws (2) "“ one near the interior door handle and the other near the reflector mount.

Step 20: Reconnect the wiring harness (1) to the back of the interior door handle's bezel, and "snap" it back into position.

Step 21: Reattach the wiring harness to the back of the trim panel (near the side mirror mount), and "snap" it back into position.



These Part Change / Installation Instructions Apply to
05 2005, 04 2004, 03 2003, 02 2002, 01 2001, 00 2000 Buick LeSabre Power Window Motor Replacement Instructions
- POPULAR GUIDES: BUICK LESABRE -

Buick LeSabre 3800 Ignition Coil Replacement

2000-2005 Buick LeSabre Alternator Replacement

2000-2005 Buick LeSabre Cabin Air Filter Replacement

2000-2005 Buick LeSabre Serpentine Engine Belt Replacement

2000-2005 Buick LeSabre Side Mirror Replacement

2000-2005 Buick LeSabre Tail Light Replacement

2000-2005 Buick LeSabre Tail Light Replacment

2000-2005 Buick LeSabre Turn Signal Replacement

2000-2005 Buick LeSabre, Pontiac Bonneville Battery Replacement


Your cart is completely and totally empty!

USERNAME (Your E-Mail)

PASSWORD
Sign UpForgot Password

Enter email address here:
  

Official PayPal Seal