1995-1996 Chevrolet Impala Hazard Warning Flasher Replacement Guide
Keep your Impala's turn signals and hazard lights working correctly by understanding this common failure point.
- A failing hazard flasher will cause your turn signals or emergency lights to stop working, work intermittently, or stay on without flashing.
- Always check for a blown fuse before assuming the flasher relay has failed.
- The flasher is located under the driver's side dashboard and is a very simple part to replace yourself.
- Aftermarket brands like Standard Ignition offer a reliable and cost-effective replacement for the original part.
Symptoms of a Failing Hazard Flasher
When the hazard flasher on your Impala starts to fail, the signs are usually straightforward. You are the eyes and ears of your vehicle, so pay attention to how your lights are behaving. Ignoring these symptoms can lead to a dangerous situation on the road.
- Turn Signals or Hazards Don't Work: The most obvious sign is when your turn signals or hazard lights stop working entirely. You might move the turn signal stalk and nothing happens, or the lights stay on without flashing.
- Lights Won't Turn Off: Less commonly, the relay can get stuck in the 'on' position. This will cause your turn signal or hazard lights to stay lit continuously, even when the switch is off.
- Hyper Flashing: If you've recently installed LED bulbs, you might notice your signals flash very rapidly. This is called "hyper flashing." While this is usually due to the lower power draw of LEDs and not a faulty flasher, some aftermarket electronic flashers are designed to correct this issue.
- No Clicking Sound: The flasher relay makes an audible clicking noise that you can hear inside the car. If you activate your turn signal and don't hear that familiar tick-tock sound from under the dashboard, the relay has likely failed. 🎬 Watch this guide to testing for common bad flasher symptoms.
Check Fuses First
Before replacing the flasher, always check the fuse box. 🎬 Check this first if your parking lamps are not working. A simple blown fuse can cause your lights to stop working and is a much easier fix. If the fuse blows repeatedly, it indicates a deeper electrical problem that needs diagnosis.
Choosing the Right Aftermarket Flasher
For the 1995-1996 Impala, you don't need to pay high dealership prices for an OEM (Original Equipment Manufacturer) flasher. Aftermarket parts are widely available, affordable, and reliable for this component. The main brand you will encounter is Standard Ignition (Standard Motor Products).
Standard Ignition (Standard Motor Products): This is a well-regarded brand in the aftermarket industry. They produce a huge range of electrical components, and their flasher relays are considered a quality replacement part. They are manufactured to meet or exceed original specifications and are a dependable choice for your Impala. Given the simplicity of this part, a Standard Ignition flasher offers the best balance of quality and cost.
| Part Type | Estimated Cost |
|---|---|
| New Aftermarket (e.g., Standard Ignition) | $10.43 - $30.57 |
| Shop Labor | $50 - $100 |
Pro Tip: DIY Installation
Replacing the hazard flasher is one of the easiest repairs you can do on your Impala. The flasher is typically located under the dashboard on the driver's side, often clipped to a bracket or just hanging among the wires. It's a simple plug-and-play part—no special tools are needed. You just pull the old one out and plug the new one in. 🎬 See how to locate and install a new flasher relay. Doing it yourself can save you up to $100 in labor costs.
Frequently Asked Questions
Where is the hazard flasher located on a 1995-1996 Impala?
The hazard flasher relay is located under the driver's side dashboard. You may need to remove the lower dash panel to access it. It is often found near the steering column, and you can sometimes locate it by turning on the hazard lights and listening for the clicking sound.
Are the turn signal and hazard flasher the same part?
On many 1995-1996 GM vehicles, including the Impala, there are two separate but identical flasher units located near each other—one for the turn signals and one for the hazard lights. If one system fails, you can sometimes swap the relays to confirm if the flasher is the problem before buying a new one.
Are there any recalls for the hazard flasher on the 1995-1996 Impala?
A search of the National Highway Traffic Safety Administration (NHTSA) database shows no specific recalls for the hazard warning flasher itself on the 1995-1996 Chevrolet Impala.
My turn signals work on one side but not the other. Is it the flasher?
Probably not. The flasher relay controls both left and right sides. If only one side is malfunctioning, the problem is more likely a burnt-out bulb, a bad socket, or a wiring issue on that specific side.
Helpful Videos
Technical Specifications
Typically a 2-prong or 3-prong electronic flasher relay. The 1995-1996 Impala often uses two separate flashers: one for turn signals and one for hazards.
We Have This Part in Stock
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Chevrolet Impala: