Chevrolet Camaro Hazard Warning Flasher Guide (1995-2002)
If your emergency lights are dead or won't flash, this guide for 4th Gen Camaro owners can help you diagnose and fix the problem.
- The hazard flasher and turn signal flasher are two separate parts on the 1995-2002 Camaro.
- Symptoms are specific: hazard lights don't work at all or stay on without flashing.
- Replacement is very easy for a DIYer, requiring only basic hand tools and about 15-30 minutes.
- Aftermarket brands like Standard Ignition offer a reliable and affordable alternative to the OEM part.
Is Your Camaro's Hazard Flasher Failing?
A bad hazard flasher is a safety concern. The symptoms are usually straightforward and point directly to this small, inexpensive part. If you experience any of these issues, the flasher relay is the most likely cause.
Common Failure Symptoms:
- No Hazard Lights: When you press the hazard switch, none of the exterior lights turn on.
- Lights On, No Flash: The hazard lights illuminate and stay on as solid lights, but they do not flash.
- Intermittent Operation: The hazard lights work sometimes and not others.
It's worth noting that if your turn signals work correctly but your hazards do not, this strongly points to a failed hazard flasher, since they are separate units on your Camaro.
Check Bulbs and Fuses First
Before replacing the flasher, always check the simple things. Make sure all your turn signal bulbs are working, as a burned-out bulb can sometimes cause electrical issues. Also, check the corresponding fuse in the fuse panel.
Choosing the Right Aftermarket Flasher
For the 1995-2002 Camaro, you have good options for a new hazard flasher without needing to pay a premium for a dealer part. The original flasher is an ACDelco part, which is GM's own brand.
Aftermarket brands like Standard Ignition (Standard Motor Products) offer direct-fit replacements that meet or exceed original specifications. Standard Ignition is a well-regarded brand whose parts are made in certified facilities, ensuring a quality part that you can rely on. Given that the price for an aftermarket Standard Ignition flasher is often very close to the ACDelco part, the choice comes down to availability. Both are solid choices for this repair.
A Note on Part Numbers
You may see two different parts from Standard Ignition, such as a metal canister type (EFL-552) and a plastic housing type (EFL-1). Both are listed for this vehicle. The key is to match the new part to the one you remove from your car. They are functionally the same but may have different mounting styles.
DIY Replacement: An Easy 15-Minute Job
Replacing the hazard flasher is one of the easiest repairs you can do on your Camaro. It requires basic tools and no complex electrical knowledge.
- Access the Panel: The flasher is located under the driver's side dashboard, behind the plastic knee bolster panel.
- Remove the Panel: Remove the two Phillips head screws at the top of the panel and two 7mm bolts from the bottom. Gently pull the panel away. You may need to disconnect the trunk release button wire. 🎬 See this walkthrough for removing the dash and swapping flashers.
- Locate the Flasher: Look up under the dash, often to the right of the steering column. 🎬 Watch: See exactly where both flasher units are located. You will see two similar flasher units. The hazard flasher is often a silver metal can or a black plastic cube plugged into a connector (sometimes red). It is separate from the turn signal flasher.
- Swap the Part: Simply unplug the old flasher from its electrical connector and plug the new one in. It only fits one way.
- Test and Reassemble: Before putting the panel back on, press your hazard switch to confirm the lights are now flashing correctly. Reinstall the knee bolster panel, and the job is done. 🎬 Watch this quick guide to identify and replace your flashers.
Cost of a New Hazard Flasher (1995-2002 Camaro)
| Part Type | Estimated Cost |
|---|---|
| New OEM (ACDelco) | $16 - $25 |
| New Aftermarket (Standard Ignition) | $10 - $31 |
| Shop Labor | $50 - $100 |
Frequently Asked Questions
Are the hazard and turn signal flashers the same part on my Camaro?
No. On the 1995-2002 Camaro, they are two separate flasher relays located near each other under the driver's side dash. This is why one system can fail while the other continues to work.
Where is the hazard flasher located?
It is under the driver's side dashboard, behind the knee panel, usually to the right of the steering column. You will need to remove the lower dash panel to see and access it.
My turn signals light up but don't flash. Is that the hazard flasher?
No, if your turn signals stay solid, that problem is caused by a bad turn signal flasher, a burned-out bulb, or a wiring issue in the turn signal circuit. The hazard flasher only controls the 4-way emergency lights.
Do I need special tools to replace the hazard flasher?
No special tools are required. You will only need a Phillips head screwdriver and a 7mm socket or wrench to remove the lower dash panel. The flasher itself unplugs by hand.
Helpful Videos
Technical Specifications
OEM Part Numbers: 19209674
2-Prong Flasher Relay
We Have This Part in Stock
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Chevrolet Camaro:
- 🎬 Helpful Videos
- 🛍️ Shop This Part
- Is Your Camaro's Hazard Flasher Failing?
- Common Failure Symptoms:
- Check Bulbs and Fuses First
- Choosing the Right Aftermarket Flasher
- A Note on Part Numbers
- DIY Replacement: An Easy 15-Minute Job
- Cost of a New Hazard Flasher (1995-2002 Camaro)
- Frequently Asked Questions
- 🎟️ Get 5% Off