Nissan Rogue Crankshaft Position Sensor: A Guide for 2008-2022 Models
Understanding the signs of a failing crankshaft sensor and how to choose the right replacement for your Rogue.
- Symptoms like stalling, no-start, and a rough idle are common signs of a failing crankshaft sensor in a Nissan Rogue.
- For Nissan vehicles, it is highly recommended to use an OEM sensor or one from an OEM supplier like Hitachi or Denso to avoid compatibility issues.
- The Check Engine Light with code P0335 is the most direct indicator of a crankshaft position sensor circuit malfunction.
- On the popular 2.5L engine, the sensor is accessible through the passenger-side wheel well and is a DIY-friendly repair for many owners.
Is Your Nissan Rogue Stalling or Hard to Start?
If your Nissan Rogue is suddenly stalling, having trouble starting, or running rough, a failing crankshaft position sensor could be the culprit. This small sensor plays a huge role in how your engine performs. When it starts to fail, it can cause a variety of noticeable problems that should not be ignored. Ignoring a bad sensor can lead to your vehicle stalling in traffic or leaving you stranded.
Common Symptoms of a Bad Crankshaft Position Sensor
A failing crankshaft position sensor often gives clear warning signs. Here’s what to look for:
- Check Engine Light: This is often the first sign. A diagnostic scan will typically show code P0335. 🎬 Watch: Diagnosing the P0335 circuit code on your Rogue.
- Difficulty Starting: The engine may crank for a long time before starting, or it may not start at all.
- Engine Stalling: The engine may stall unexpectedly, especially after it has warmed up.
- Rough Idle and Misfires: The engine may run poorly, shake, or vibrate at idle. This can also be felt as a stumble during acceleration.
- Poor Acceleration: You might notice your Rogue is sluggish and doesn't accelerate as it should.
- Reduced Fuel Economy: Incorrect timing signals can cause the engine to use more fuel than normal.
Known Issues: Recalls and Service Bulletins
While there are no specific recalls for the crankshaft position sensor itself on 2008-2022 Nissan Rogues, some newer 2023-2025 models with the 1.5L turbo engine have been recalled for issues with potential engine failure and stalling. These recalls involve reprogramming the Engine Control Module (ECM). Additionally, a Technical Service Bulletin (TSB) for the 2017-2020 Rogue Sport noted issues like long crank times and stalling, which were also addressed with an ECM reprogram. While your vehicle may not be under these specific actions, the symptoms are very similar to a failing crank sensor. It is always wise to check for any open recalls or TSBs for your specific VIN.
Choosing the Right Aftermarket Sensor
When it comes to electronic sensors for Nissan vehicles, not all aftermarket brands are created equal. For critical parts like the crankshaft position sensor, using a high-quality replacement is essential for long-term reliability. Owner forums and mechanic experience strongly suggest that Nissan engines are sensitive to the quality of their electronic sensors.
Here’s a breakdown of brand quality tiers to help you choose:
- Tier 1: OEM Supplier (Hitachi, Denso): Hitachi is widely known to be the Original Equipment Manufacturer (OEM) for many of Nissan's engine sensors. Choosing a Hitachi or Denso sensor often means you are getting the exact same quality part that came in the Nissan box, but without the dealership price tag. These are the most recommended options.
- Tier 2: Reputable Aftermarket (Beck Arnley, Standard Ignition, NGK): Brands like Beck Arnley and Standard (also sold as Intermotor) have a long-standing reputation for producing reliable aftermarket parts for import vehicles. They are a solid choice if an OEM supplier part is not available.
- Tier 3: Value-Oriented (Dorman, Walker Products, others): These brands offer a direct-fit replacement at a very competitive price. While they can be a good budget-friendly solution, for a critical sensor on a Nissan, many owners prefer to spend a bit more for the peace of mind that comes with an OEM-level part.
Pro Tip: Replace Cam and Crank Sensors Together?
For some Nissan engines, particularly the 2.5L QR25DE found in many Rogues, mechanics often recommend replacing the camshaft position sensors at the same time as the crankshaft position sensor. An old Nissan service campaign noted that new sensors might not communicate well with older, unchanged sensors. While not strictly required, replacing them as a set can prevent future issues and save on labor down the road.
| Part Type | Estimated Cost |
|---|---|
| New Aftermarket Sensor | $29.95 - $122.51 |
| New OEM Sensor | $90 - $150 |
| Shop Labor | $75 - $150 |
Frequently Asked Questions
Where is the crankshaft position sensor located on a Nissan Rogue?
On the 2.5L engine, the sensor is located on the back side of the engine block, near where the engine meets the transmission. It is typically accessed by removing the front passenger-side wheel and splash shield. 🎬 Watch: Finding and replacing the sensor on older Rogues. On the newer 1.5L turbo engines, there are two sensors located on the lower front side of the engine.
Is this a difficult part to replace myself?
For the common 2.5L engine, the replacement is considered DIY-feasible for someone with basic mechanical skills. It involves jacking up the vehicle, removing the wheel, and accessing the sensor through the wheel well. The sensor is held in by a single 10mm bolt. 🎬 See this step-by-step replacement guide for 2014-2020 models. The main difficulty can be reaching the sensor and disconnecting the electrical connector in a tight space.
Should I buy an OEM sensor from the dealer?
While you can always buy the part from a Nissan dealer for guaranteed compatibility, you can get the same quality by purchasing a sensor from the OEM supplier, such as Hitachi. This often provides the best balance of quality and value. Many owners have reported issues with budget-friendly sensors, leading them to do the job twice.
What happens if I don't replace a bad crankshaft sensor?
Ignoring the symptoms can lead to more significant problems. Your vehicle will become increasingly unreliable, with more frequent stalling and hard starting. Eventually, the sensor will fail completely, and your engine will not start at all, potentially leaving you stranded.
Helpful Videos
Technical Specifications
OEM Part Numbers: 23731-JA00C 23731-JA00B 23731-JA00A 23731-1VA0A 23731-6RC3A 23731-6CA0B
The crankshaft position sensor for the Nissan Rogue is typically a Magnetic Resistance Element (MRE) type sensor. It is held in place by a single 10mm bolt and uses a standard electrical connector. Part numbers vary significantly based on the engine (2.5L vs. 2.0L vs. 1.5L) and model year, so verifying the correct part for your specific vehicle is crucial.
We Have This Part in Stock
The information in this article is provided for general reference and educational purposes only. Vehicle specifications, procedures, and part compatibility can vary by production date, trim level, and region. Always consult your vehicle's factory service manual and verify part numbers before purchasing or performing repairs. Safety-critical components such as airbags, seat belts, and braking systems should be installed by a qualified professional.
- Nissan Rogue:
- 🎬 Helpful Videos
- 🛍️ Shop This Part
- Is Your Nissan Rogue Stalling or Hard to Start?
- Common Symptoms of a Bad Crankshaft Position Sensor
- Known Issues: Recalls and Service Bulletins
- Choosing the Right Aftermarket Sensor
- Pro Tip: Replace Cam and Crank Sensors Together?
- Frequently Asked Questions
- 🎟️ Get 5% Off