ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.807, Axle Nut Socket Size: 0.945, Axle Nut Thread Size: M14x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 23.425, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 33, Product Condition: New, Shaft Diameter: 1.063, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3390131

$130.08 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Window, Axle Nut Included: No, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 25.125, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: Shafts Are Inspected 100% For Run Out To Prevent Vibrations. Only Shafts That Meet The Specifications For Run Out Are Utilized In The Remanufacturing Of A Cv Drive Axle Assembly., FAA_A10: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAA_A11: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A12: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A3: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A4: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A5: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A6: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A7: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A8: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A9: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAQ_Q1: Are The Cv Drive Axle Shafts Balanced At The Factory?, FAQ_Q10: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, FAQ_Q11: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q12: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q3: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q4: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q5: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q6: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q7: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q8: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q9: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Spline, Outboard Spline Quantity: 38, Product Condition: Remanufactured, Shaft Diameter: 1.66, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Right (Cardone)

Partslink #: 60-7243

$122.96 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Window, Axle Nut Included: Yes, Axle Nut Socket Size: 0.748, Axle Nut Thread Size: M16x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 20.875, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 38, Product Condition: New, Shaft Diameter: 1.665, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-7052

$133.41 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Window, Axle Nut Included: Yes, Axle Nut Thread Size: M14x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 25, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 33, Product Condition: New, Shaft Diameter: 1.654, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Right (Cardone)

Partslink #: 66-7329

$126.67 View part →

✓ In Stock

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3339442

$134.11 View part →

✓ In Stock

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3491454

$127.95 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Window, Axle Nut Included: Yes, Axle Nut Socket Size: 0.748, Axle Nut Thread Size: M16x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 20.438, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 38, Product Condition: New, Shaft Diameter: 1.275, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-7350

$139.55 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Window, Axle Nut Included: Yes, Axle Nut Socket Size: 0.748, Axle Nut Thread Size: M16x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 19.688, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 38, Product Condition: New, Shaft Diameter: 1.67, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Right (Cardone)

Partslink #: 66-7053

$136.38 View part →

✓ In Stock

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3349636

$151.64 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Window, Axle Nut Included: Yes, Axle Nut Length: 0.551, Axle Nut Socket Size: 0.748, Axle Nut Thread Size: M16x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 24.213, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 38, Product Condition: New, Shaft Diameter: 1.063, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2002-2008 Audi A4 Quattro CV Axle Assembly - Front Right (Cardone)

Partslink #: 66-7302

$144.10 View part →

✓ In Stock

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3484385

$153.06 View part →

✓ In Stock

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3444998

$150.12 View part →

✓ In Stock

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3422029

Chas: -195500

$153.90 View part →

✓ In Stock

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3422205

$151.64 View part →

✓ In Stock

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3364602

$160.46 View part →

✓ In Stock

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3484687

$160.46 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Window, Axle Nut Included: Yes, Axle Nut Socket Size: 0.748, Axle Nut Thread Size: M16x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 22.625, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 38, Product Condition: New, Shaft Diameter: 1.275, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2005-2009 Audi A4 Quattro CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-7383

$161.85 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 45, ABS Tone Ring Type: Window, Axle Nut Included: Yes, Axle Nut Socket Size: 1.063, Axle Nut Thread Size: M16x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 24.252, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 6, Inboard Joint Type: Bolt-on, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 38, Product Condition: New, Shaft Diameter: 1.213, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2003-2009 Audi A4 Quattro CV Axle Assembly - Rear Left or Rear Right (Cardone)

Partslink #: 66-7380

$166.43 View part →

✓ In Stock

2002-2004 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3358197

Chas: -350000

$170.18 View part →

✓ In Stock

2002-2004 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-4114022

Chas: -350000

$170.18 View part →

✓ In Stock

2002-2005 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3350096

Chas: -035 000

$231.20 View part →

✓ In Stock

2009-2011 Audi A4 Quattro CV Axle Assembly - Rear Left or Rear Right (Autopart International)

Partslink #: W0133-4224382

w/ Torque Vectoring Differential

$203.48 View part →

✓ In Stock

2005-2009 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3411124

$244.32 View part →

✓ In Stock

2009-2011 Audi A4 Quattro CV Axle Assembly - Rear or Rear Left or Rear Right (Autopart International)

Partslink #: W0133-4382872

Production: -08/15/2011, Except Torque Vectoring Differential

$209.43 View part →

✓ In Stock

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Left (GKN Loebro)

Partslink #: 301212

100 MM

$294.15 View part →

✓ In Stock

2011-2016 Audi A4 Quattro CV Axle Assembly - Rear Left or Rear Right (Autopart International)

Partslink #: W0133-4382926

Production: 08/15/2011-, Except Torque Vectoring Differential

$267.81 View part →

✓ In Stock

2005-2009 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3480881

$317.52 View part →

✓ In Stock

2002-2005 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3338373

Chas: -035 000

$271.44 View part →

✓ In Stock

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Left (GKN Loebro)

Partslink #: 304617

123MM inner Joint (4.84 inches)

$357.14 View part →

✓ In Stock

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3406365

Chas: -195550

$277.16 View part →

✓ In Stock

2009 Audi A4 Quattro CV Axle Assembly - Front Left (GKN Loebro)

Partslink #: 304923

$383.22 View part →

✓ In Stock

1998-2000 Audi A4 Quattro CV Axle Assembly - Front Right (GKN Loebro)

Partslink #: 301209

130MM inner joint (5.11 inches) Tripodic From vin 8D-W-007 800

$282.03 View part →

✓ In Stock

2005-2008 Audi A4 Quattro CV Axle Assembly - Front Left (GKN Loebro)

Partslink #: 305069

From vin 8E-5-400 001

$442.71 View part →

✓ In Stock

2011-2016 Audi A4 Quattro CV Axle Assembly - Rear Right (Autopart International)

Partslink #: W0133-4382820

Production: 08/15/2011-, w/ Torque Vectoring Differential

$292.14 View part →

✓ In Stock

2002-2005 Audi A4 Quattro CV Axle Assembly - Front Right (GKN Loebro)

Partslink #: 304288

$362.69 View part →

✓ In Stock

2005-2009 Audi A4 Quattro CV Axle Assembly - Front Right (GKN Loebro)

Partslink #: 305083

From vin 8E-5-400 001

$390.17 View part →

✓ In Stock

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Right (GKN Loebro)

Partslink #: 305082

Length 509.7 mm INCLUDES NEW hub bolt M16x1.5

$489.16 View part →

✓ In Stock

1996-2001 Audi A4 Quattro CV Axle Assembly - Rear (Autopart International)

Partslink #: W0133-3428721

$132.03 View part →

✓ In Stock

2013-2016 Audi A4 Quattro CV Axle Assembly - Front (Autopart International)

Partslink #: W0133-4382816

$179.91 View part →

✓ In Stock

2002-2009 Audi A4 Quattro CV Axle Assembly - Rear (Autopart International)

Partslink #: W0133-3443277

$198.29 View part →

✓ In Stock

2021-2022 Audi A4 Quattro CV Axle Assembly - Front (Autopart International)

Partslink #: W0133-3492534

w/ Uncoupling Feature

$212.30 View part →

✓ In Stock

2017-2020 Audi A4 Quattro CV Axle Assembly - Front (Autopart International)

Partslink #: W0133-4382889

$234.42 View part →

✓ In Stock

2009-2012 Audi A4 Quattro CV Axle Assembly - Front (Vaico)

Partslink #: W0133-1818721

$370.14 View part →

✓ In Stock

2009-2012 Audi A4 Quattro CV Axle Assembly - Front (GKN Loebro)

Partslink #: 304924

with 123mm inboard joint

$380.46 View part →

Audi A4 Quattro CV Axle Assembly Replacement

1996-2001 Audi A4 Quattro CV Axle Assembly - Rear Left or Rear Right (Cardone)

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Left (Cardone)

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Right (Cardone)

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Left (Cardone)

1999-2000 Audi A4 Quattro CV Axle Assembly - Front Right (Cardone)

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Right (Cardone)

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Left (Cardone)

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Right (Cardone)

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Left (Cardone)

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Right (Cardone)

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

2002-2008 Audi A4 Quattro CV Axle Assembly - Front Right (Cardone)

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

1997-2000 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

2005-2009 Audi A4 Quattro CV Axle Assembly - Front Left (Cardone)

2003-2009 Audi A4 Quattro CV Axle Assembly - Rear Left or Rear Right (Cardone)

2002-2004 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

2002-2004 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

2002-2005 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

2009-2011 Audi A4 Quattro CV Axle Assembly - Rear Left or Rear Right (Autopart International)

2005-2009 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

2009-2011 Audi A4 Quattro CV Axle Assembly - Rear or Rear Left or Rear Right (Autopart International)

1996-2001 Audi A4 Quattro CV Axle Assembly - Front Left (GKN Loebro)

2011-2016 Audi A4 Quattro CV Axle Assembly - Rear Left or Rear Right (Autopart International)

2005-2009 Audi A4 Quattro CV Axle Assembly - Front Left (Autopart International)

2002-2005 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Left (GKN Loebro)

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Right (Autopart International)

2009 Audi A4 Quattro CV Axle Assembly - Front Left (GKN Loebro)

1998-2000 Audi A4 Quattro CV Axle Assembly - Front Right (GKN Loebro)

2005-2008 Audi A4 Quattro CV Axle Assembly - Front Left (GKN Loebro)

2011-2016 Audi A4 Quattro CV Axle Assembly - Rear Right (Autopart International)

2002-2005 Audi A4 Quattro CV Axle Assembly - Front Right (GKN Loebro)

2005-2009 Audi A4 Quattro CV Axle Assembly - Front Right (GKN Loebro)

2002-2006 Audi A4 Quattro CV Axle Assembly - Front Right (GKN Loebro)

1996-2001 Audi A4 Quattro CV Axle Assembly - Rear (Autopart International)

2013-2016 Audi A4 Quattro CV Axle Assembly - Front (Autopart International)

2002-2009 Audi A4 Quattro CV Axle Assembly - Rear (Autopart International)

2021-2022 Audi A4 Quattro CV Axle Assembly - Front (Autopart International)

2017-2020 Audi A4 Quattro CV Axle Assembly - Front (Autopart International)

2009-2012 Audi A4 Quattro CV Axle Assembly - Front (Vaico)

2009-2012 Audi A4 Quattro CV Axle Assembly - Front (GKN Loebro)

What buyers are saying.

Racing Partner Videos

CV Axle Assembly Compatibility for Audi A4 Quattro

Available Trims

Body Types

Engine Options

Transmissions