Chevrolet Camaro Differential Spool Replacement

8.2 in. 10 Bolt; For Use w/28 Spline Axles GM 8.2 in.; For Use w/28 Spline Axles

10 Bolt with 30 Spline Teeth with GM 8.5 Axle

8.5 in. 10 Bolt; For Use w/28 Spline Axles GM 8.5 in.; For Use w/28 Spline Axles

Dana 44/Reverse; For Use w/30 Spline Axles Dana 44; For Use w/30 Spline Axles

8.5 in. 10 Bolt; For Use w/30 Spline Axles GM 8.5 in.; For Use w/30 Spline Axles

For GM 8.5" (10 Bolt); 30 Spline; Full Spool; Steel; 1999 And Later Requires Use Of Bearing LM603049 And Race LM603012; 1998 And Earlier Use Bearing LM102949 And Race LM102911; 45 Degree Pressure Angle; C-Clip Eliminator Required

For GM 8.5" (10 Bolt); 28 Spline; Full Spool; Steel; Requires Use Of Bearing LM501349 And Race LM501314; 45 Degree Pressure Angle; C-Clip Eliminator Required

For GM 8.875" (12 Bolt); 30 Spline; Full Spool; 45 Degree Pressure Angle; C-Clip Eliminator Required; Steel

with 28 Spline Teeth with GM 7.5 & 7.6 Axles

with 26 Spline Teeth with GM 7.5 & 7.6 Axles

For GM 8.5" (10 Bolt); 28 Spline; Full Spool; Steel; Requires Use Of Bearing LM501349 And Race LM501314; 45 Degree Pressure Angle; C-Clip Eliminator Required

10 Bolt with 28 Spline Teeth with GM 8.5 Axle

8.875 in. 12 Bolt; For Use w/30 Spline Axles GM 12 Bolt Passenger Car; For Use w/30 Spline Axles

28 Spline GM 7.5 in. and 7.6 in.; 28 Spline

For GM 8.875" (12 Bolt); 35 Spline; Full Spool; C-Clip Eliminator Required; Steel

For GM 8.5" (10 Bolt); 33 Spline; Full Spool; Steel; 45 Degree Pressure Angle; C-Clip Eliminator Required

7.5 in. 10 Bolt; For Use w/26 Spline Axles GM 7.5 in. and 7.6 in.; For Use w/26 Spline Axles

Dana 44/Reverse; For Use w/30 Spline Axles; Steel; 3.92 Ratio And Up Dana 44; For Use w/30 Spline Axles; Steel; 3.92 Ratio And Up

Dana 44/Reverse; For Use w/30 Spline Axles; Steel; 3.73 Ratio And Down Dana 44; For Use w/30 Spline Axles; Steel; 3.73 Ratio And Down

8.875 in. 12 Bolt; For Use w/30 Spline Axles; 4.10 Ratio And Up GM 12 Bolt Passenger Car; For Use w/30 Spline Axles; 4.10 Ratio And Up

8.6 in./8.5 in. 10 Bolt; For Use w/30 Spline Axles; Steel GM 8.5 in.; For Use w/30 Spline Axles; Steel

with Full Spool Case Split 3.73 And Down with 30 Splines with Dana 44 Axle

with Full Spool Case Split 3.92 And Up with 30 Splines with Dana 44 Axle