Chevrolet G10 Differential Replacement

GM 12 Bolt Truck; 30 Spline; 2.73 - 3.42 Ratio~Yukon Dura Grip Positraction; GM 12 Bolt Truck; 30 Spline; Fits 2.73 - 3.42 Ratio or Thick Gears

30 Spline; 1.30 in. Axle Shaft Diameter; 2.76 - 3.42 Ring Gear Pinion Ratio; Rear 8.875 in.

30 Spline; 1.32 in. Axle Shaft Diameter; 2.73 And Up Ring Gear Pinion Ratio; Rear 8.5 in./8.6 in. For Axles w/Small bearing Bores Race O.D. 2.89 in. LM102949/LM102911 Req.~Axles w/Large Bearing Bores Race O.D. 3.06 in. LM603049/LM603012 Req.

12 Bolt GM; 30 Spline; 3.73 And Up GM 12 Bolt Truck; 30 Spline; 3.73 And Up~Yukon Dura Grip Positraction; GM 12 Bolt Truck; 30 Spline; 3.73 And Up

30 Spline; 1.50 in. Axle Shaft Diameter; Rear 10.5 in.; All Ratios Replaces Conventional Diff. Internals In Certain 1973 Thru Present GM Axles~If Installed In GM Axle Equiped w/Optional Eaton Diff. Will Require~New Gear Support Case Assembly GM PN[6258336 Or 6258340] Depending On Ratio

30 Spline; 1.30 in. Axle Shaft Diameter; 3.73 And Up Ring Gear Pinion Ratio; Also Fits GM Half Ton Truck

30 Spline; 1.32 in. Axle Shaft Diameter; 2.73 And Up Rng Gear Pin. Rat;Manual Locking Hubs Are Recomnd For Some Appl.; 8.5 in./8.6 in. For Axles w/Small bearing Bores Race O.D. 2.89 in. LM102949/LM102911 Req.~Axles w/Large Bearing Bores Race O.D. 3.06 in. LM603049/LM603012 Req.~Manual Locking Hubs Recommended For Front Axle Applications

30 Spline; 1.30 in. Axle Shaft Diameter; 3.73 And Up Ring Gear Pinion Ratio; Rear 8.875 in. For Axles w/Small bearing Bores Race O.D. 2.89 in. LM102949/LM102911 Req.~Axles w/Large Bearing Bores Race O.D. 3.06 in. LM603049/LM603012 Req.

33 Spline; 1.37 in. Axle Shaft Diameter; 9.5 in.

35 Spline; 1.50 in. Axle Shaft Diameter; 4.10 And Down Ring Gear Pinion Ratio; Rear Dana 60

35 Spline; 1.50 in. Axle Shaft Diameter; 4.10 And Down Ring Gear Pinion Ratio; Dana 60HD

8.6 in. 10 Bolt; 30 Spline; 2.73 And Up GM 8.5 in.; 30 Spline; 2.73 And Up~Yukon Dura Grip Positraction / Limited Slip; GM 8.5 in. Rear; 30 Spline; 2.73 And Up; 1.781 in. Bearing Journal

28 Spline; 2.73 And Up GM 8.5 in.; 28 Spline; 2.73 And Up~Yukon Dura Grip Positraction / Limited Slip; GM 8.5 in. Rear; 28 Spline; 2.73 And Up; 1.781 in. Bearing Journal

30 Spline; 1.50 in. Axle Shaft Diameter; 4.10 And Down Ring Gear Pinion Ratio; Rear 10.5 in.

35 Spline; 1.50 in. Axle Shaft Diameter; 4.10 And Down Ring Gear Pinion Ratio; Dana 60HD; Dana 60

35 Spline; 1.50 in. Axle Shaft Diameter; 4.56 And Up Ring Gear Pinion Ratio; Dana 60HD; Dana 60

GM 10.5 in.; 14 Bolt; 30 Spline; 4.10 And Down Ring Gear Pinion Ratio; 1.50 in. Axle Shaft Diameter

30 Spline; 1.32 in. Axle Shaft Diameter; 2.73 And Up Ring Gear Pinion Ratio; Rear 8.5 in.; Rear 8.6 in. For Axles w/Small bearing Bores Race O.D. 2.89 in. LM102949/LM102911 Req.~Axles w/Large Bearing Bores Race O.D. 3.06 in. LM603049/LM603012 Req.

2.73 Gear Ratio And Up GM 8.5 in.; 2.73 Gear Ratio And Up~GM 8.5 in.; Yukon Grizzly Locker; 2.73 Gear Ratio And Up; 1.78 in. Bearing Journals; Uses LM102949/ LM102911 Carrier Bearings

30 Spline; 1.30 in. Axle Shaft Diameter; 3.73 And Up Ring Gear Pinion Ratio; Rear 8.875 in.

35 Spline; 1.50 in. Axle Shaft Diameter; 4.56 And Up Ring Gear Pinion Ratio; Dana 70B; Rear Dana 70

33 Spline; 1.37 in. Axle Shaft Diameter; Rear 9.5 in.; All Ratios

35 Spline; 1.50 in. Axle Shaft Diameter; 4.56 And Up Ring Gear Pinion Ratio; Rear Dana 60

35 Spline; 1.50 in. Axle Shaft Diameter; 4.56 And Up Ring Gear Pinion Ratio; Dana 60HD

35 Spline; 1.50 in. Axle Shaft Diameter; 4.10 And Down Ring Gear Pinion Ratio; Rear Dana 70

35 Spline; 1.50 in. Axle Shaft Diameter; 4.10 And Down Ring Gear Pinion Ratio; Dana 70HD; Rear Dana 70

Axle: GM 12 bolt truck 8.875" Shaft: 1.31" Spline: 30 Ratio: 3.73 and up Confirm axle is 12 bolt not 44 or GM 10 bolt

Open To Lock; 35 Spline; 4.56 Gear Ratio Up Dana 60

Dana 44; 30 Spline; 3.92 And Up Ring Gear Pinion Ratio; 1.31 in. Axle Shaft Diameter

Axle: GM 10 bolt 8.5/8.6" Shaft: 1.31" Spline: 30 Ratio: 2.73 and up confirm 28 or 30 spline shafts

Axle: GM 10 bolt 8.5/8.6" Shaft: 1.20" Spline: 28 Ratio: 2.73 and up confirm 28 or 30 spline shafts

Dana 44; 30 Spline; 3.73 And Down Ring Gear Pinion Ratio; 1.31 in. Axle Shaft Diameter

30 Spline; 1.32 in. Axle Shaft Diameter; 2.73 And Up Ring Gear Pinion Ratio; 8.5 in./8.6 in. For Axles w/Small bearing Bores Race O.D. 2.89 in. LM102949/LM102911 Req.~Axles w/Large Bearing Bores Race O.D. 3.06 in. LM603049/LM603012 Req.

Selectable Full Locker w/Limited Slip; For Use w/2.76-3.42 Ratio; 3 Series Case; 30 Spline 8.875 in. (12 Bolt)

Selectable Full Locker w/Limited Slip; For Use w/2.73-Up Ratio; 30 Spline 8.5 in. (10 Bolt)

Open To Lock; 35 Spline; 4.10 Gear Ratio Down Dana 60

Open To Lock; 30 Spline; 4.56 Gear Ratio Up Dana 60

Selectable Full Locker w/Limited Slip; For Use w/2.73-Up Ratio; 28 Spline 8.5 in. (10 Bolt)

Open To Lock; 30 Spline; 4.10 Gear Ratio Down Dana 60

Selectable Full Locker w/Limited Slip; For Use w/3.73-Up Ratio; 4 Series Case; 30 Spline 8.875 in. (12 Bolt)

Dana 70; 35 Spline; 1.50 in. Axle Shaft Diameter; 4.56 And Up Ring Gear Pinion Ratio; 10.5 in. Ring Gear Diameter

Dana 70; 35 Spline; 1.50 in. Axle Shaft Diameter; 4.10 And Down Ring Gear Pinion Ratio; 10.5 in. Ring Gear Diameter