Chevrolet Impala Exhaust Muffler Replacement

Modifications and/or Additional Parts May Be Required for Installation

DIRECT FIT MSL/MAXIMUM Muffler System With Rear Resonator

Modifications and/or Additional Parts May Be Required for Installation

Modifications and/or Additional Parts May Be Required for Installation

with Dual Exhaust with 18 (in) Muffler Body Modifications and/or Additional Parts May Be Required for Installation

Modifications and/or Additional Parts May Be Required for Installation

Modifications and/or Additional Parts May Be Required for Installation

with 18 (in) Muffler Body Modifications and/or Additional Parts May Be Required for Installation

Modifications and/or Additional Parts May Be Required for Installation

with Dual Exhaust

If welded assembly, replace all required parts

If welded assembly, replace all required parts

If welded assembly, replace all required parts

DIRECT FIT MSL/MAXIMUM Muffler OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.

Except Partial Zero Emissions Vehicle (PZEV) If welded assembly, replace all required parts

Except Partial Zero Emissions Vehicle (PZEV) If welded assembly, replace all required parts

If welded assembly, replace all required parts

If welded assembly, replace all required parts

If welded assembly, replace all required parts

DIRECT FIT MSL/MAXIMUM Muffler OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.

For Vehicles Originally Equipped with 1 Catalytic Converter(s) If welded assembly, replace all required parts

If welded assembly, replace all required parts

with Single Exhaust

2.25 Offset In/2.25 Offset Out; Clamp On; 409 Stainless Steel Not Direct Fit-Some Adaptation Required

2.25 Offset In/2.25 Center Out; Clamp On; 409 Stainless Steel Not Direct Fit-Some Adaptation Required

For Vehicles Originally Equipped with 1 Catalytic Converter(s) If welded assembly, replace all required parts

If welded assembly, replace all required parts

2.25 in. Offset Inlet/Center Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; Aluminized Steel Not Direct Fit-Some Adaptation Required

2.25 in. Offset Inlet/Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; Aluminized Steel Not Direct Fit-Some Adaptation Required

2.25 in. Offset Inlet/Center Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; 409 Stainless Steel

2.25 in. Offset Inlet/Opposite Side Offset Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; 409 Stainless Steel

2.25 in. Offset Inlet/Center Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; Aluminized Steel Not Direct Fit-Some Adaptation Required

2 in. Offset Inlet/Center Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; Aluminized Steel Not Direct Fit-Some Adaptation Required

2.25 in. Offset Inlet/Center Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; 409 Stainless Steel Not Direct Fit-Some Adaptation Required

2 in. Offset Inlet/Opposite Side Offset Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; Aluminized Steel Not Direct Fit-Some Adaptation Required

2 in. Center Inlet/Offset Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; Aluminized Steel Not Direct Fit-Some Adaptation Required

Direct Fit; Oval; 4.25 in. x 9.75 in.;RH(Passenger) Side; 2.25 in. ID; 2.5 in. OD; 14 in. Shell Length; 21.25 in. Overall Length RH Side

Direct Fit; Oval; 4.25 in. x 9.75 in.;LH(Driver) Side; 2.25 in. ID; 2.5 in. OD; 14 in. Shell Length; 21.25 in. Overall Length LH Side

2.25 in. Offset Inlet/2.25 in. Opposite Side Offset Outlet; Case Dimensions 4 in. x 9.75 in. x 13 in.; 19 in. Overall Length; Aluminized Steel Not Direct Fit-Some Adaptation Required

2.25 in. Offset Inlet/Center Outlet; Case Dimensions 4 in. x 9.75 in. x 17 in.; 23 in. Overall Length; Aluminized Steel Not Direct Fit-Some Adaptation Required

2 in. Offset Inlet/Center Outlet; Case Dimensions 4 in. x 9.75 in. x 17 in.; 23 in. Overall Length; Aluminized Steel Not Direct Fit-Some Adaptation Required

2.25 in. Offset Inlet/Opposite Side Offset Outlet; Case Dimensions 4 in. x 9.75 in. x 17 in.; 23 in. Overall Length; Aluminized Steel Not Direct Fit-Some Adaptation Required

2.25 in. Offset Inlet/Center Outlet; Case Dimensions 4 in. x 9.75 in. x 17 in.; 23 in. Overall Length; 409 Stainless Steel Not Direct Fit-Some Adaptation Required

2.25 in. Offset Inlet/Opposite Side Offset Outlet; Case Dimensions 4 in. x 9.75 in. x 17 in.; 23 in. Overall Length; 409 Stainless Steel Not Direct Fit-Some Adaptation Required

2.5 in. Center Inlet/Outlet; Oval; 4 in. x 5 in. x 18 in.; 409 Stainless Steel Not Direct Fit-Some Adaptation Required