Chevrolet V2500 Suburban Differential Replacement

30 Spline; 1.32 in. Axle Shaft Diameter; 2.73 And Up Ring Gear Pinion Ratio; Rear 8.5 in./8.6 in. For Axles w/Small bearing Bores Race O.D. 2.89 in. LM102949/LM102911 Req.~Axles w/Large Bearing Bores Race O.D. 3.06 in. LM603049/LM603012 Req.

30 Spline; 1.32 in. Axle Shaft Diameter; 2.73 And Up Rng Gear Pin. Rat;Manual Locking Hubs Are Recomnd For Some Appl.; 8.5 in./8.6 in. For Axles w/Small bearing Bores Race O.D. 2.89 in. LM102949/LM102911 Req.~Axles w/Large Bearing Bores Race O.D. 3.06 in. LM603049/LM603012 Req.~Manual Locking Hubs Recommended For Front Axle Applications

33 Spline; 1.37 in. Axle Shaft Diameter; 9.5 in.

30 Spline GM 10.5 in Rear; Yukon Grizzly Locker; 30 Spline; Installs into Standard Open Carrier Case; Diffenetial has 14 Bolt Cover & Removable Pinion Support~GM 10.5 in.; 14 Bolt Cover; 30 Spline

8.6 in. 10 Bolt; 30 Spline; 2.73 And Up GM 8.5 in.; 30 Spline; 2.73 And Up~Yukon Dura Grip Positraction / Limited Slip; GM 8.5 in. Front; 30 Spline; 2.73 And Up; 1.781 in. Bearing Journal

28 Spline; 2.73 And Up GM 8.5 in.; 28 Spline; 2.73 And Up~Yukon Dura Grip Positraction / Limited Slip; GM 8.5 in. Front; 28 Spline; 2.73 And Up; 1.781 in. Bearing Journal

40 Spline

9.5 in. 14 Bolt; 33 Spline Axles GM 9.5 in.; 14 bolt cover; 33 Spline Axles~Yukon Dura Grip Positraction; GM 9.5 in. Rear; 14 bolt cover; 33 Spline

30 Spline; 1.32 in. Axle Shaft Diameter; 2.73 And Up Ring Gear Pinion Ratio; Rear 8.5 in.; Rear 8.6 in. For Axles w/Small bearing Bores Race O.D. 2.89 in. LM102949/LM102911 Req.~Axles w/Large Bearing Bores Race O.D. 3.06 in. LM603049/LM603012 Req.

2.73 Gear Ratio And Up GM 8.5 in.; 2.73 Gear Ratio And Up~GM 8.5 in.; Yukon Grizzly Locker; 2.73 Gear Ratio And Up; 1.78 in. Bearing Journals; Uses LM102949/ LM102911 Carrier Bearings

33 Spline; 1.37 in. Axle Shaft Diameter; Rear 9.5 in.; All Ratios

10.5 in. 14 Bolt; 4.10 And Down GM 10.5 in.; 14 Bolt Cover; 4.10 And Down~Yukon Dura Grip Positraction; GM 10.5 in. / 14T Rear; 14 Bolt Cover; 30 Spline; 4.10 And Down or Thick Gears

30 Spline; 1.32 in. Axle Shaft Diameter; 2.73 And Up Ring Gear Pinion Ratio; 8.5 in./8.6 in. For Axles w/Small bearing Bores Race O.D. 2.89 in. LM102949/LM102911 Req.~Axles w/Large Bearing Bores Race O.D. 3.06 in. LM603049/LM603012 Req.

Selectable Full Locker w/Limited Slip; For Use w/2.73-Up Ratio; 30 Spline 8.5 in. (10 Bolt)