Buy Dodge Dart Turn Signal Light Bulbs

The Dodge Dart turn signal light bulb-also called an indicator bulb, blinker bulb, or directional lamp bulb-tells other drivers when you plan to turn or change lanes. Model-year charts show the front socket typically accepts size 7444NA/7443 while the rear uses 3157-type dual-filament bulbs for 2013-2016 Darts (AutoZone.com, dodge-dart.org). Federal and state rules require an amber or white front signal that can be seen from 500 ft, and a red or amber rear signal (Transport Canada, Washington State Legislature). Swapping a failed incandescent bulb for a modern LED can boost brightness five-fold, but you may need "CAN-bus" resistors or an EP27 electronic flasher to cure hyper-flash (YouTube, Reddit). Recalls on 2013-2016 Darts (NHTSA 19V-293) highlight why keeping these bulbs working matters for safety (NHTSA Static, NHTSA). Simple hand tools and five minutes per corner are all that's needed for replacement-saving tickets and collisions while keeping your Dart legal.

Turn-signal bulbs sit in the front bumper corners and tail-lamp clusters. They flash in sync with the dash arrow to warn traffic of your intent, reducing crash risk by up to 18 percent, according to NHTSA research . On Darts equipped with mirror-mounted repeaters, small LEDs inside the side mirrors illuminate too (Dealer Process).

← scroll table horizontally →

• Cross-Reference: 7444NA can interchange with 7440, 7443, 7442NA, WY21/5W, W21/5W (SEALIGHT).
• Always match socket type-CK vs. non-CK-before buying to avoid pin-polarity issues (dodge-dart.org).
• Use an amber bulb up front; white-switchback LEDs that glow amber when blinking are also legal (NHTSA).

Incandescent (stock): Cheap and color-stable but draw ~27 W and last ~1-2 years (AutoZone.com, Sylvania Automotive).
Halogen upgrade: Slightly brighter, similar draw, rated 2 × life.
LED retrofit: Up to 4000 lumens per pair, 90 % less power, 15-year service life, instant on-off for clearer signaling (Amazon, Diode Dynamics).

• Dash arrow blinks twice as fast (hyper-flash).
• One side stays solid without blinking.
• "Turn Signal Lamp Out" warning message on the instrument cluster (Dealer Process).
• Other drivers honk or wave because they can't read your intentions.
• Bulb shows black soot inside glass.

LED swaps often lower circuit load, confusing the flasher relay. Two cures:

1. Load resistors (6 Ω-50 W) spliced in parallel with each LED-simple but adds heat (YouTube, Next Level Neo).
2. LED-specific flasher relay (EP27/FL27)-plug-and-play, draws almost no heat (eBay).

Tip: Mount resistors to metal away from plastic to avoid melting lens housings.

• FMVSS 108 sets minimum brightness, color, and spacing for U.S. turn lamps (Transport Canada).
• Federal Motor Carrier Safety regs echo the amber/red color rule (NHTSA).
• Many states, like Washington (RCW 46.37.200), require visibility to 500 ft in sunlight (Washington State Legislature).
• Amber rear signals cut certain crash types by 5.3 % versus red - one reason safety advocates urge amber adoption (The Drive).

1. Open Hood or Trunk. Remove plastic retainers or two T-20 Torx screws to access the lamp (YouTube).
2. Twist Socket Counter-clockwise and pull out.
3. Press and Turn Bulb to remove. Wear gloves-oil from skin shortens life.
4. Insert New Bulb (match amber coating forward).
5. Test Flash Rate before reassembling. Add resistor or flash-fix relay if blink is rapid (Reddit).
6. Re-attach Housing firmly; water leaks ruin circuitry.

• Check signals monthly-burned-out bulbs are a ticketable offense (whittenbrothers.com).
• Excess vibration, moisture, or high system voltage shortens bulb life (The Spruce).
• Keep lens clear; foggy plastic cuts signal brightness by 20 % or more.

Incandescent and LED turn bulbs contain small metal parts and glass. Wrap spent bulbs in paper before trashing, or take them to a household-hazardous-waste site to avoid injuries (The Home Depot, The Spruce). Some e-recycling centers accept LEDs for materials recovery.

Q: What bulb size is in my 2014 Dodge Dart front blinker?
A: Most trims use a 7444NA or 7443 wedge-base amber bulb (AutoZone.com).

Q: Can I use white LEDs that switch to amber when flashing?
A: Yes-"switchback" LEDs meet federal color rules because they display amber during the actual turn signal (NHTSA).

Q: Why did my dash start blinking twice as fast after I installed LEDs?
A: That's hyper-flash. Add load resistors or swap to an EP27 LED-ready relay to restore normal rate (YouTube, eBay).

Q: Do I need two bulbs or four for a full replacement?
A: Replace bulbs in pairs (both fronts or both rears) so brightness stays even, which helps other drivers judge distance (Sylvania Automotive).

Q: Are brighter bulbs legal?
A: Yes, as long as they remain within FMVSS 108 photometric limits and are amber-colored up front (Transport Canada).

Q: How long do LED indicator bulbs last?
A: Quality LEDs are rated up to 50,000 hours-roughly 15 years of normal driving (Amazon).

Q: Is there a recall on Dart turn signals?
A: Yes, recall 19V-293 covers 2013-2016 Darts for lamp-out warnings; check your VIN at the NHTSA recall portal (NHTSA Static, NHTSA).

Q: Can I mix LED front bulbs with incandescent rear bulbs?
A: Mixing is safe, but hyper-flash may still occur. If it does, address the flasher circuit or add resistors (Reddit).

Q: What tools will I need?
A: A flat screwdriver, a T-20 Torx driver, and gloves are enough for most Dodge Dart signal bulb jobs (YouTube).

Replacing or upgrading your Dodge Dart turn signal light bulb is a quick win for safety, style, and peace of mind-keep those blinker bulbs bright and traffic will thank you.