Ford F-250 Differential Ring and Pinion Replacement

Front/Rear; Dana 44; 10 Cover Bolts; 10 Ring Gear Bolts; 30 Axle Spline; 26 Pinion Spline; Standard Rotation

with 4.27 Gear Ratio with Dana Model 44 Axle

with 3.54 Gear Ratio with Dana 44 IFS Axle

with 4.56 Gear Ratio with Dana 44 Axle with Thick Gear - For use with 3.73 Gear Ratio and Down Carrier Case

with 5.13 Gear Ratio with Dana Model 44 Axle

with 4.09 Gear Ratio with Dana 44 Axle with Thick Gear - For use with 3.73 Gear Ratio and Down Carrier Case

with 4.56 Gear Ratio with Dana Model 44 IFS Axle

with 4.56 Gear Ratio with Dana Model 44 Axle

with 216mm Diameter Ring Gear with 5.13 Gear Ratio with Dana Model 44 Axle with Reverse Rotation

with 4.09 Gear Ratio with Dana 44 Axle with Standard Gear

with 216mm Diameter Ring Gear with 5.38 Gear Ratio with Dana Model 44 Axle with Reverse Rotation

with 3.54 Gear Ratio with Dana 44 Axle

Dana 50 Axle Reverse Rotation w/5.13 Axle Ratio

Dana 50 Axle Reverse Rotation w/3.73 Axle Ratio

with 4.56 Gear Ratio with Dana 60 Axle

Front/ Dana 60; 10 Cover Bolts; 12 Ring Gear Bolts; 35 Axle Spline; 29 Pinion Spline; Both Rotation

Reverse Rotation - Turn Input Shaft Clockwise & Output Shaft will Turn Counter-Clockwise with 4.88 Gear Ratio with Dana 60 Axle

with 5.13 Gear Ratio with Dana 44 Axle with Thick Gear - For use with 3.73 Gear Ratio and Down Carrier Case

with 5.38 Gear Ratio with Dana Model 44 Axle

with 4.88 Gear Ratio with Ford 10.25 Axle

Reverse Rotation - Turn Input Shaft Clockwise & Output Shaft will Turn Counter-Clockwise with 5.13 Gear Ratio with Dana 60 Axle

with 4.88 Gear Ratio with Dana 60 Axle

Reverse Rotation - Turn Input Shaft Clockwise & Output Shaft will Turn Counter-Clockwise with 4.30 Gear Ratio with Dana 60 Axle

with 5.86 Gear Ratio with Dana 60 Axle

with 3.54 Gear Ratio with Dana 50 Axle

with 4.88 Gear Ratio with Frod 8.8 IFS Axle with Reverse Rotation

with 4.56 Gear Ratio with For 8.8 IFS Reverse Rotation Axle

with 216mm Diameter Ring Gear with 4.11 Gear Ratio with Dana Model 44 Axle with Reverse Rotation

For Ford 8.8" (10 Bolt); A-Line Ring and Pinion; 4.56 Ratio; Requires Notched Cross Pin 80-0273-1 (3/4") or 80-0279-1 (7/8") For Ring Gear Clearance

with 5.38 Gear Ratio with Dana 60 Axle

For Dana 44; 5.13 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Dana 44; 3.73 Ratio; Requires a 3.73 and Numerically Lower Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Dana 44; 4.56 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

with 3.73 Gear Ratio with Dana 50 Axle

For Ford 8.8" (10 Bolt); A-Line Ring and Pinion; 4.10 Ratio

For Dana 44; 4.89 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

with 5.89 Gear Ratio with Dana Model 44 Axle

For Dana 44; 4.27 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Dana 44; 3.07 Ratio; Requires a 3.73 and Numerically Lower Ratio Carrier

For Dana 60; 4.10 Ratio; Requires a 4.10 and Numerically Lower Ratio Carrier

For Dana 60; 4.56 Ratio; Requires a 4.56 and Numerically Higher Ratio Carrier

For Ford 8.8" (10 Bolt); A-Line Ring and Pinion; 3.55 Ratio

For Dana 44; 3.92 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Dana 44; 5.38 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier

Dana 50 Axle Reverse Rotation w/4.30 Axle Ratio

For Dana 44; 4.88 Ratio; Thick Ring Gear; Requires a 3.73 and Numerically Lower Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Ford 8.8" (10 Bolt); A-Line Ring and Pinion; 3.73 Ratio

with 4.10 Gear Ratio with Ford 9.75 Axle

For Dana 60; 5.38 Ratio; Thick Ring Gear; Requires a 4.10 and Numerically Lower Ratio Carrier

For Dana 70; 5.86 Ratio; Has 5/8" Offset Of Pinion; Requires a 4.56 and Numerically Higher Ratio Carrier

For Dana 70; 3.73 Ratio; Has 5/8" Offset Of Pinion; Requires a 4.10 and Numerically Lower Ratio Carrier

with 3.54 Gear Ratio with Dana 60 Axle

For Dana 60; 4.88 Ratio; Thick Ring Gear; Requires a 4.10 and Numerically Lower Ratio Carrier

For Dana 44; 4.09 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Dana 44; 4.89 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier

For Dana 44; 5.38 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Ford 8.8" (10 Bolt); 3.55 Ratio

For Dana 44; 4.09 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier

For Dana 60; 4.88 Ratio; Requires a 4.56 and Numerically Higher Ratio Carrier

For Dana 44; 4.56 Ratio; Thick Ring Gear; Requires a 3.73 and Numerically Lower Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Dana 60; 5.86 Ratio; Requires a 4.56 and Numerically Higher Ratio Carrier

Dana 50 Axle Reverse Rotation w/3.54 Axle Ratio

with 4.56 Gear Ratio with Ford 10.25 Axle

For Dana 60; 3.54 Ratio; Requires a 4.10 and Numerically Lower Ratio Carrier

Fits 8.8 in. ; Front; 4.10 Gear Ratio; 8.8 in. Ring Gear Dia.; Incl. Crush Collar/Pinion Nut/Pinion Bearing/Pinion Seal/Ring Gear Bolts

For Dana 44; 5.13 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier

8.8 In. Ring Gear w/3.73 Axle Ratio

with Reverse Rotation with 216mm Diameter Ring Gear with 4.88 Gear Ratio with Dana Model 44 Axle

For Dana 60; 5.38 Ratio; Requires a 4.56 and Numerically Higher Ratio Carrier

For Dana 70; 3.54 Ratio; Has 5/8" Offset Of Pinion; Requires a 4.10 and Numerically Lower Ratio Carrier

with 4.88 Gear Ratio with Dana Model 44 Axle

For Dana 70; 4.10 Ratio; Has 5/8" Offset Of Pinion; Requires a 4.10 and Numerically Lower Ratio Carrier

For Dana 60; 5.13 Ratio; Thick Ring Gear; Requires a 4.10 and Numerically Lower Ratio Carrier

For Dana 44; 5.89 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Ford 8.8" (10 Bolt); 4.10 Ratio

For Dana 60; 4.10 Ratio; Requires a 4.10 and Numerically Lower Ratio Carrier

Dana 44 Axle w/4.09 Axle Ratio

For Dana 60; 3.73 Ratio; Requires a 4.10 and Numerically Lower Ratio Carrier

10.25 In. Ring Gear w/3.73 Axle Ratio

For Dana 44; 5.38 Ratio; Thick Ring Gear; Requires 3.73 and Numerically Lower Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Dana 60; 5.13 Ratio; Requires a 4.56 and Numerically Higher Ratio Carrier

with 4.88 Gear Ratio with Dana 44 Axle with Thick Gear - For use with 3.73 Gear Ratio and Down Carrier Case

with 3.92 Gear Ratio with Dana 44 Axle with Thick Gear - For use with 3.73 Gear Ratio and Down Carrier Case

For Dana 44; 3.54 Ratio; Requires a 3.73 and Numerically Lower Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Ford 10.25" (12 Bolt); Long Pinion; 5.38 Ratio

with Thick Gear Case Split 4.10 And Down with 4.56 Gear Ratio with Dana 60 Reverse Rotation Axle

For Ford 8.8" (10 Bolt); 4.56 Ratio; Requires Notched Cross Pin 80-0273-1 (3/4") or 80-0279-1 (7/8") For Ring Gear Clearance

with 3.73 Gear Ratio with Ford 10.25 Axle

Reverse Rotation - Turn Input Shaft Clockwise & Output Shaft will Turn Counter-Clockwise with 5.38 Gear Ratio with Dana 60 Axle

with 3.55 Gear Ratio with Ford 9.75 Axle

with 4.30 Gear Ratio with Dana 50 IFS Axle

with 4.56 Gear Ratio with Dana 50 IFS Axle

with 31 Splines with Ford 10.5 Axle

For Ford 8.8" (10 Bolt); 3.73 Ratio

with 5.13 Gear Ratio with Dana 50 IFS Axle

For Dana 60; 4.56 Ratio; Thick Ring Gear; Requires a 4.10 and Numerically Lower Ratio Carrier

For Dana 44; 4.56 Ratio; Requires a 3.92 and Numerically Higher Ratio Carrier

Reverse Rotation - Turn Input Shaft Clockwise & Output Shaft will Turn Counter-Clockwise with 3.54 Gear Ratio with Dana 60 Axle

with 7.17 Gear Ratio with Dana Model 60 Axle

with 4.10 Gear Ratio with Ford 10.25 Axle

Rear; Ford 10.50 in.; 12 Cover Bolts; 12 Ring Gear Bolts; 35 Axle Spline; 31 Pinion Spline; Standard Rotation; Fits 1999-2007 Applications

8.8 In. Ring Gear w/4.56 Axle Ratio

Carrier Break 3.73/3.92 Dana 44 Axle Reverse Rotation w/3.73 Axle Ratio

with 3.73 Gear Ratio with Dana 60 Axle

For Dana 60; 5.13 Ratio; Thick Ring Gear; Requires a 4.10 and Numerically Lower Ratio Carrier

Dana 60 Axle w/3.54 Axle Ratio

Dana 60 Axle w/4.10 Axle Ratio

with 4.10 Gear Ratio with Dana 60 Axle

For Ford 10.25" (12 Bolt); Long Pinion; 4.89 Ratio

with 4.56 Gear Ratio with Ford 9.75 Axle

with 3.73 Gear Ratio with Ford 9.75 Axle

with 5.13 Gear Ratio with Dana Model 60 Axle

8.8 In. Ring Gear w/4.10 Axle Ratio

Dana 44 Reverse; 3.73 Ratio Dana 44 Front; Reverse Rotation; Ring and Pinion Set; 3.73 Ratio; 26 Spline Pinion~Dana 44; Reverse Rotation; Straight Axle; 3.73 Ratio; Reverse Rotation

For Ford 8.8" (10 Bolt); 4.88 Ratio; Requires Notched Cross Pin 80-0273-1 (3/4") or 80-0279-1 (7/8") For Ring Gear Clearance

with 5.13 Gear Ratio with Frod 8.8 IFS Axle with Reverse Rotation

with 5.13 Gear Ratio with Ford 9.75 Axle

with 4.88 Gear Ratio with Ford 9.75 Axle

For Ford 10.25" (12 Bolt); Long Pinion; 3.73 Ratio

For Ford 8.8" (10 Bolt); 3.27 Ratio

8.8 In. Ring Gear w/3.55 Axle Ratio

For Ford 8.8" (10 Bolt); 3.08 Ratio

For Dana 44; 3.54 Ratio; Requires a 3.73 and Numerically Lower Ratio Carrier

For Ford 8.8" IFS; Performance Ring and Pinion; 4.56 Ratio

Dana 44; 4.88 Ratio; 3.73 And Down Carrier; Double Drilled Ring Gear Works w/3/8in. And 7/16in. Bolt Dana 44; Standard Rotation; 4.88 Ratio; 3.73 And Down Carrier; Double Drilled Ring Gear Works w/3/8in. And 7/16in. Bolt~Dana 44; Standard Rotation; 4.88 Ratio; Thick Ring and Pinion Set; 26 Spline Pinion; Fits 3 Series Carrier; Double Drilled Ring Gear for 3/8in. and 7/16in. Bolts

For Ford 10.25" (12 Bolt); Long Pinion; 4.10 Ratio

10.25 In. Ring Gear w/4.10 Axle Ratio

For Ford 8.8" (10 Bolt); Performance Ring and Pinion; 3.55 Ratio

For Ford 8.8" (10 Bolt); Performance Ring and Pinion; 3.73 Ratio

For Ford 10.25" (12 Bolt); Long Pinion; 3.55 Ratio

For Ford 10.25" (12 Bolt); Long Pinion; 4.56 Ratio

For Ford 8.8" IFS; Performance Ring and Pinion; 4.88 Ratio

For Ford 8.8" (10 Bolt); Performance Ring and Pinion; 4.10 Ratio

8.8 in. Reverse; 3.73 Ratio Ford 8.8 in. Front; Reverse Rotation; Ring and Pinion Set; 3.73 Ratio~Ford 8.8 in.; Reverse; 3.73 Ratio; Reverse Rotation

For Ford 10.25" (12 Bolt); Short Pinion; 3.55 Ratio

For Dana 60; 5.38 Ratio; Requires a 4.56 and Numerically Higher Ratio Carrier

For Ford 8.8" (10 Bolt); Performance Ring and Pinion; 4.56 Ratio; Requires Notched Cross Pin 80-0273-1 (3/4") or 80-0279-1 (7/8") For Ring Gear Clearance

For Ford 8.8" (10 Bolt); Performance Ring and Pinion; 4.30 Ratio

For Ford 8.8" (10 Bolt); Performance Ring and Pinion; 3.90 Ratio

Dana 60/Reverse; 4.30 Ratio Dana 60 Front; Reverse Rotation; Thick Ring and Pinion Set; 4.30 Ratio; Fits 3 Series 4.10 & Down Carrier~Dana 60; Reverse Rotation; 4.30 Ratio

For Ford 10.25" (12 Bolt); Short Pinion; 4.10 Ratio

For Ford 8.8" (10 Bolt); Performance Ring and Pinion; 4.88 Ratio; Requires Notched Cross Pin 80-0273-1 (3/4") or 80-0279-1 (7/8") For Ring Gear Clearance

Bolts Not Included with 3.73 Gear Ratio with Dana 60 Axle

9.75 In. Ring Gear w/3.55 Axle Ratio

For Ford 8.8" (10 Bolt); Performance Ring and Pinion; 3.31 Ratio

9.75 In. Ring Gear w/3.73 Axle Ratio

For Ford 8.8" IFS; Performance Ring and Pinion; 3.73 Ratio

Dana 44 Reverse; 5.38 Ratio Dana 44 Front; Reverse Rotation; Ring and Pinion Set; 5.38 Ratio; 26 Spline Pinion~Dana 44; Reverse Rotation; Straight Axle; 5.38 Ratio; Reverse Rotation

Dana 44 Reverse; Reverse Rotation; 4.88 Ratio Dana 44 Front; Reverse Rotation; Ring and Pinion Set; 4.88 Ratio; 26 Spline Pinion~Dana 44; Reverse Rotation; Straight Axle; 4.88 Ratio; Reverse Rotation

Dana 44 Reverse; 4.56 Ratio Dana 44 Front; Reverse Rotation; Ring and Pinion Set; 4.56 Ratio; 26 Spline Pinion~Dana 44; Reverse Rotation; Straight Axle; 4.56 Ratio; Reverse Rotation

Dana 44 Reverse; 4.11 Ratio Dana 44 Front; Reverse Rotation; Ring and Pinion Set; 4.11 Ratio; 26 Spline Pinion~Dana 44; Reverse Rotation; Straight Axle; 4.11 Ratio; Reverse Rotation

Dana 44 Reverse; 5.13 Ratio Dana 44 Front; Reverse Rotation; Ring and Pinion Set; 5.13 Ratio; 26 Spline Pinion~Dana 44; Reverse Rotation; Straight Axle; 5.13 Ratio; Reverse Rotation

For Ford 8.8" IFS; Performance Ring and Pinion; 4.10 Ratio

For Dana 44; 5.89 Ratio; Thick Ring Gear; Requires 3.73 and Numerically Lower Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

Dana 44; 4.88 Ratio Dana 44; Standard Rotation; 4.88 Ratio~Dana 44; Standard Rotation; Ring and Pinion Set; 4.88 Ratio; 26 Spline Pinion; Fits 4 Series Carrierr; Double Drilled Ring Gear for 3/8in. and 7/16in. Bolts

For Ford 8.8" (10 Bolt); Performance Ring and Pinion; 5.14 Ratio; Requires Notched Cross Pin 80-0273-1 (3/4") or 80-0279-1 (7/8") For Ring Gear Clearance

Bolts Not Included with 4.10 Gear Ratio with Dana 60 Axle

Dana 50; Reverse Rotation; 4.88 Ratio Dana 50; Straight Axle; 4.88 Ratio

Dana 50; 4.56 Ratio Dana 50; Straight Axle; 4.56 Ratio

Dana 44; 3.73 Ratio Dana 44; Standard Rotation; 3.73 Ratio~Dana 44; Standard Rotation; Ring and Pinion Set; 3.73 Ratio; 26 Spline Pinion; Fits 3 Series Carrier

8.8 in. Reverse; 4.88 Ratio Ford 8.8 in. Front; Reverse Rotation; Ring and Pinion Set; 4.88 Ratio~Ford 8.8 in.; Reverse; 4.88 Ratio; Reverse Rotation

Dana 44; Standard Rotation; 3.08 Ratio~Dana 44; Standard Rotation; Ring and Pinion Set; 3.08 Ratio; 26 Spline Pinion; Fits 3 Series Carrier

Dana 44; 3.92 Ratio Dana 44; Standard Rotation; 3.92 Ratio~Dana 44; Standard Rotation; Ring and Pinion Set; 3.92 Ratio; 26 Spline Pinion; Fits 4 Series Carrier

Dana 44; 4.56:1 Ratio; 1.375 in. Pinion; 26 Spline; 8.500 in. Ring Gear; Set Dana 44; Standard Rotation; 4.56 Ratio; 1.375 in. Pinion; 26 Spline; 8.500 in. Ring Gear; Set~Dana 44; Standard Rotation; Ring and Pinion Set; 4.56 Ratio; 26 Spline Pinion; Fits 4 Series Carrier

8.8 in. Reverse; 5.13 Ratio Ford 8.8 in. Front; Reverse Rotation; Ring and Pinion Set; 5.13 Ratio~Ford 8.8 in.; Reverse; 5.13 Ratio; Reverse Rotation

Dana 44; 4.11 Ratio; Thick Ring/Pinion; 3.73-Down Carrier Dana 44; Standard Rotation; 4.11 Ratio; Thick Ring and Pinion Set; 26 Spline Pinion; Fits 3 Series Carrier~Dana 44; Standard Rotation; 4.11 Ratio; Thick Ring/Pinion; 3.73-Down Carrier

Dana 44; 3.54 Ratio Dana 44; Standard Rotation; 3.54 Ratio~Dana 44; Standard Rotation; Ring and Pinion Set; 3.54 Ratio; 26 Spline Pinion; Fits 3 Series Carrier

Dana 50; Reverse Rotation; 5.38 Ratio Dana 50; Straight Axle; 5.38 Ratio

Dana 44; 4.11 Ratio Dana 44; Standard Rotation; 4.11 Ratio~Dana 44; Standard Rotation; Ring and Pinion Set; 4.11 Ratio; 26 Spline Pinion; Fits 4 Series Carrier

Dana 44; 3.31 Ratio Dana 44; Standard Rotation; 3.31 Ratio~Dana 44; Standard Rotation; Ring and Pinion Set; 3.31 Ratio; 26 Spline Pinion; Fits 3 Series Carrier

Bolts Not Included with 5.38 Gear Ratio with Dana 60 Axle

with 4.56 Gear Ratio with Dana 60 Axle with Thick Gear

For Ford 8.8" (10 Bolt); Performance Ring and Pinion; 5.71 Ratio; Requires Notched Cross Pin 80-0273-1 (3/4") or 80-0279-1 (7/8") For Ring Gear Clearance

For Ford 8.8" (10 Bolt); 3.73 Ratio

Dana 50; Reverse Rotation; 5.13 Ratio Dana 50; Straight Axle; 5.13 Ratio

10.5 in. 14 Bolt; High Performance; 3.55 Gear Ratio Ford 10.5 in. Rear; Ring and Pinion Set; 3.55 Gear Ratio; 31 Spline Pinion~Ford 10.5 in.; High Performance; 3.55 Gear Ratio; 31 Spline Pinion

10.25 in. 12 Bolt; 10.5 in. 14 Bolt; 4.88 Ratio Ford 10.25 in. Rear; Ring and Pinion Set; 4.88 Ratio; 1.5 in. Long Pinion Spline; 1992 & older had short pinion splines. a new yoke is required when being replaced with the long design.~Ford 10.25 in.; 4.88 Ratio

Dana 50; 3.73 Ratio Dana 50; Straight Axle; 3.73 Ratio; Reverse Rotation

Dana 44 Reverse; 3.54 Ratio Dana 44 Front; Reverse Rotation; Ring and Pinion Set; 3.54 Ratio; 26 Spline Pinion~Dana 44; Reverse Rotation; Straight Axle; 3.54 Ratio; Reverse Rotation

For Dana 70; 4.56 Ratio; Has 5/8" Offset Of Pinion; Thick Ring Gear; Requires a 3.73 and Numerically Lower Ratio Carrier

Dana 44; 5.89 Ratio Dana 44; Standard Rotation; 5.89 Ratio~Dana 44; Standard Rotation; Ring and Pinion Set; 5.89 Ratio; 26 Spline Pinion; Fits 4 Series Carrierr; Double Drilled Ring Gear for 3/8in. and 7/16in. Bolts

Dana 50; 4.30 Ratio Dana 50; Straight Axle; 4.30 Ratio

Dana 44; 5.13 Ratio Dana 44; Standard Rotation; 5.13 Ratio~Dana 44; Standard Rotation; Ring and Pinion Set; 5.13 Ratio; 26 Spline Pinion; Fits 4 Series Carrierr; Double Drilled Ring Gear for 3/8in. and 7/16in. Bolts

Dana 50; Reverse Rotation; 4.11 Ratio Dana 50; Straight Axle; 4.11 Ratio

For Dana 60; 4.56 Ratio; Thick Ring Gear; Requires a 4.10 and Numerically Lower Ratio Carrier; 1994-2002 Front Or Rear Dodge Ram Applications Requires Preload Shims Part# 1118

10.5 in. 14 Bolt; 4.56 Ratio Ford 10.5 in. Rear; Ring and Pinion Set; 4.56 Ratio; 31 Spline Pinion~Ford 10.5 in.; 4.56 Ratio; 31 Spline Pinion

10.5 in. 14 Bolt; 4.88 Ratio Ford 10.5 in. Rear; Ring and Pinion Set; 4.88 Ratio; 31 Spline Pinion~Ford 10.5 in.; 4.88 Ratio; 31 Spline Pinion

10.25 in. 12 Bolt; 10.5 in. 14 Bolt; 3.55 Ratio Ford 10.25 in. Rear; Ring and Pinion Set; 3.55 Ratio; 1.5 in. Long Pinion Spline; 1992 & older had short pinion splines. a new yoke is required when being replaced with the long design.~Ford 10.25 in.; 3.55 Ratio

For Ford 8.8" (10 Bolt); 4.30 Ratio

For Ford 8.8" (10 Bolt); 4.10 Ratio

Dana 60 Reverse; High Performance Replacement; 4.56 Gear Ratio Dana 60 Front; Reverse Rotation; Thick Ring and Pinion Set; 4.56 Ratio; Fits 3 Series Carrier 4.10& Down Carrier~Dana 60; Reverse Rotation; High Performance Replacement; 4.56 Gear Ratio

Dana 60 Reverse; 4.88 Ratio Dana 60 Front; Reverse Rotation; Thick Ring and Pinion Set; 4.88 Ratio; Fits 3 Series 4.10 & Down Carrier~Dana 60; Reverse Rotation; 4.88 Ratio

with 5.38 Gear Ratio with Ford 10.25 Axle

For Dana 60; 4.10 Ratio; Thin Gear; Requires a 4.56 and Numerically Higher Ratio Carrier

Bolts Not Included with 7.17 Gear Ratio with Dana 60 Axle

For Dana 60; 4.30 Ratio; Thick Ring Gear; Requires a 4.10 and Numerically Lower Ratio Carrier

For Dana 60; 4.56 Ratio; Requires a 4.56 and Numerically Higher Ratio Carrier

For Dana 60; 5.13 Ratio; Requires a 4.56 and Numerically Higher Ratio Carrier

Dana 60/Irregular Cover; 4.56 Ratio Dana 60; 4.56 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 4.56 Ratio; Fits 4 Series Carrier

Dana 60/Irregular Cover; 5.13 Ratio Dana 60; 5.13 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 5.13 Ratio; Fits 4 Series Carrier

Dana 60 Irregular Cover; Dana 60; 4.11 Ratio Dana 60; 4.11 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 4.11 Ratio; Fits 3 Series Carrier

Dana 60; 5.13 Gear Ratio Dana 60; 5.13 Ratio; Thick

High Performance Replacement; Dana 60; 5.38 Gear Ratio Dana 60; 5.38 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 5.38 Ratio; Fits 4 Series Carrier

Dana 60; 4.56 Gear Ratio Dana 60; 4.56 Ratio~Dana 60; 4.56 Ratio; thick for 4.10 and down carrier~Dana 60; 4.56 Ratio;Dana 60; 4.56 Ratio. thick for 4.10 and down carrier

Dana 60; 4.88 Gear Ratio Dana 60; 4.88 Gear Ratio~Dana 60; Standard Rotation; 4.88 Ratio; Thick Ring and Pinion Set; Fits 3 Series Carrier

For Dana 60; 4.88 Ratio; Requires a 4.56 and Numerically Higher Ratio Carrier

For Dana 60; 3.54 Ratio; Requires a 4.10 and Numerically Lower Ratio Carrier

Bolts Not Included with 3.54 Gear Ratio with Dana 60 Axle

For Ford 8.8" (10 Bolt); 4.56 Ratio; Requires Notched Cross Pin 80-0273-1 (3/4") or 80-0279-1 (7/8") For Ring Gear Clearance

Dana 60 Reverse; 5.13 Ratio Dana 60 Front; Reverse Rotation; Thick Ring and Pinion Set; 5.13 Ratio; Fits 3 Series 4.10 & Down Carrier~Dana 60; Reverse Rotation; 5.13 Ratio

Dana 60/Reverse; 5.38 Ratio; Thin; Fits 4.56 Case Dana 60 Front; Reverse Rotation; Ring and Pinion Set; 5.38 Ratio; Fits 4 Series 4.56 & Up Carrier~Dana 60; Reverse Rotation; 5.38 Ratio; Thin; Fits 4.56 Case

Dana 60 Reverse; High Performance Replacement; 5.38 Gear Ratio Dana 60 Front; Reverse Rotation; Thick Ring and Pinion Set; 5.38 Ratio; Fits 3 Series 4.10 & Down Carrier~Dana 60; Reverse Rotation; High Performance Replacement; 5.38 Gear Ratio

Dana 44; 4.56:1 Ratio; 1.375 in. Pinion; 26 Spline; 8.500 in. Ring Gear; Thick; Set Dana 44; Standard Rotation; 4.56 Ratio; 1.375 in. Pinion; 26 Spline; 8.500 in. Ring Gear; Thick; Set~Dana 44; Standard Rotation; 4.56 Ratio; Thick Ring and Pinion Set; 26 Spline Pinion; Fits 3 Series Carrier; Double Drilled Ring Gear for 3/8in. and 7/16in. Bolts

Dana 44; 5.38 Ratio Dana 44; Standard Rotation; 5.38 Ratio~Dana 44; Standard Rotation; Ring and Pinion Set; 5.38 Ratio; 26 Spline Pinion; Fits 4 Series Carrierr; Double Drilled Ring Gear for 3/8in. and 7/16in. Bolts

10.25 in. 12 Bolt; 10.5 in. 14 Bolt; 5.13 Ratio Ford 10.25 in. Rear; Ring and Pinion Set; 5.13 Ratio; 1.5 in. Long Pinion Spline; 1992 & older had short pinion splines. a new yoke is required when being replaced with the long design.~Ford 10.25 in.; 5.13 Ratio

For Ford 10.5" (12 Bolt); 5.38 Ratio; Includes Inner And Outer Pinion Bearings Only; Includes 10.25" Late Ring/Pinion w/ 10.25" Inner/Outer Pinion Bearings, Do Not Substitute; Use Ford 10.25" Installation Kits

For Ford 10.5" (12 Bolt); 3.55 Ratio; Includes Inner And Outer Pinion Bearings Only; Includes 10.25" Late Ring/Pinion w/ 10.25" Inner/Outer Pinion Bearings, Do Not Substitute; Use Ford 10.25" Installation Kits

For Ford 10.5" (12 Bolt); 4.56 Ratio; Includes Inner And Outer Pinion Bearings Only; Includes 10.25" Late Ring/Pinion w/ 10.25" Inner/Outer Pinion Bearings, Do Not Substitute; Use Ford 10.25" Installation Kits

For Ford 8.8" (10 Bolt); 3.31 Ratio

Dana 60/Reverse; High Performance Replacement; 4.88 Gear Ratio Dana 60; High Performance Replacement; 4.88 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 4.88 Ratio; Fits 4 Series Carrier

10.5 in. 14 Bolt; 3.73 Ratio Ford 10.5 in. Rear; Ring and Pinion Set; 3.73 Ratio; 31 Spline Pinion~Ford 10.5 in.; 3.73 Ratio; 31 Spline Pinion

10.5 in. 14 Bolt; 4.11 Ratio Ford 10.5 in. Rear; Ring and Pinion Set; 4.11 Ratio; 31 Spline Pinion~Ford 10.5 in.; 4.11 Ratio; 31 Spline Pinion

10.5 in. 14 Bolt; 4.30 Ratio Ford 10.5 in. Rear; Ring and Pinion Set; 4.30 Ratio; 31 Spline Pinion~Ford 10.5 in.; 4.30 Ratio; 31 Spline Pinion

Dana 44; 5.13 Ratio; 3.73 And Down Carrier; Double Drilled Ring Gear Works w/3/8in. And 7/16in. Bolt Dana 44; Standard Rotation; 5.13 Ratio; 3.73 And Down Carrier; Double Drilled Ring Gear Works w/3/8in. And 7/16in. Bolt~Dana 44; Standard Rotation; 5.13 Ratio; Thick Ring and Pinion Set; 26 Spline Pinion; Fits 3 Series Carrier; Double Drilled Ring Gear for 3/8in. and 7/16in. Bolts

10.25 in. 12 Bolt; 10.5 in. 14 Bolt; 3.73 Ratio Ford 10.25 in. Rear; Ring and Pinion Set; 3.73 Ratio; 1.5 in. Long Pinion Spline; 1992 & older had short pinion splines. a new yoke is required when being replaced with the long design.~Ford 10.25 in.; 3.73 Ratio

10.25 in. 12 Bolt; 10.5 in. 14 Bolt; 4.11 Ratio Ford 10.25 in. Rear; Ring and Pinion Set; 4.11 Ratio; 1.5 in. Long Pinion Spline; 1992 & older had short pinion splines. a new yoke is required when being replaced with the long design.~Ford 10.25 in.; 4.11 Ratio

10.25 in. 12 Bolt; 10.5 in. 14 Bolt; 5.38 Ratio Ford 10.25 in. Rear; Ring and Pinion Set; 5.38 Ratio; 1.5 in. Long Pinion Spline; 1992 & older had short pinion splines. a new yoke is required when being replaced with the long design.~Ford 10.25 in.; 5.38 Ratio

Reverse Rotation - Turn Input Shaft Clockwise & Output Shaft will Turn Counter-Clockwise with 3.73 Gear Ratio with Dana 60 Axle

For Dana 44; 5.13 Ratio; Thick Ring Gear; Requires a 3.73 and Numerically Lower Ratio Carrier; Dual Drilled for 3/8" and 7/16" Ring Gear Bolts

For Ford 8.8" IFS; Performance Ring and Pinion; 5.29 Ratio

For Ford 8.8" (10 Bolt); 4.88 Ratio; Requires Notched Cross Pin 80-0273-1 (3/4") or 80-0279-1 (7/8") For Ring Gear Clearance

8.8 in. Reverse; 4.56 Ratio Ford 8.8 in. Front; Reverse Rotation; Ring and Pinion Set; 4.56 Ratio~Ford 8.8 in.; Reverse; 4.56 Ratio; Reverse Rotation

10.25 in. 12 Bolt; 10.5 in. 14 Bolt; 4.56 Ratio Ford 10.25 in. Rear; Ring and Pinion Set; 4.56 Ratio; 1.5 in. Long Pinion Spline; 1992 & older had short pinion splines. a new yoke is required when being replaced with the long design.~Ford 10.25 in.; 4.56 Ratio~Long spline pinion

10.25 in. 12 Bolt; 10.5 in. 14 Bolt; 4.30 Ratio Ford 10.25 in. Rear; Ring and Pinion Set; 4.30 Ratio; 1.5 in. Long Pinion Spline; 1992 & older had short pinion splines. a new yoke is required when being replaced with the long design.~Ford 10.25 in.; 4.30 Ratio

For Ford 10.5" (12 Bolt); 4.10 Ratio; Includes Inner And Outer Pinion Bearings Only; Includes 10.25" Late Ring/Pinion w/ 10.25" Inner/Outer Pinion Bearings, Do Not Substitute; Use Ford 10.25" Installation Kits

For Ford 10.5" (12 Bolt); 3.73 Ratio; Includes Inner And Outer Pinion Bearings Only; Includes 10.25" Late Ring/Pinion w/ 10.25" Inner/Outer Pinion Bearings, Do Not Substitute; Use Ford 10.25" Installation Kits

8.8 in. Reverse; Reverse Rotation; 4.11 Ratio Ford 8.8 in. Front; Reverse Rotation; Ring and Pinion Set; 4.11 Ratio~Ford 8.8 in.; Reverse; 4.11 Ratio; Reverse Rotation

For Dana 60; 3.73 Ratio; Requires a 4.10 and Numerically Lower Ratio Carrier

8.8 in. Reverse; 3.31 Ratio Ford 8.8 in. Front; Reverse Rotation; Ring and Pinion Set; 3.31 Ratio~Ford 8.8 in.; Reverse; 3.31 Ratio; Reverse Rotation

8.8 in. Reverse; 3.55 Ratio Ford 8.8 in. Front; Reverse Rotation; Ring and Pinion Set; 3.55 Ratio~Ford 8.8 in.; Reverse; 3.55 Ratio; Reverse Rotation

For Ford 10.5" (12 Bolt); 4.89 Ratio; Includes Inner And Outer Pinion Bearings Only; Includes 10.25" Late Ring/Pinion w/ 10.25" Inner/Outer Pinion Bearings, Do Not Substitute; Use Ford 10.25" Installation Kits

Dana 60/Irregular Cover; 6.17 Ratio Dana 60; 6.17 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 6.17 Ratio; Fits 4 Series Carrier

Dana 60/Irregular Cover; 4.10 And Down; 4.30 Ratio; Will Work w/4.27 in 4WD Dana 60; 4.10 And Down; 4.30 Ratio; Will Work w/4.27 in 4WD~Dana 60; Standard Rotation; Ring and Pinion Set; 4.30 Ratio; Fits 3 Series Carrier; Will Work w/4.27 in 4WD

Dana 60/Irregular Cover; 5.86 Ratio Dana 60; 5.86 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 5.86 Ratio; Fits 4 Series Carrier

Dana 60/Reverse; 3.73 Ratio Dana 60 Front; Reverse Rotation; Ring and Pinion Set; 3.73 Ratio; Fits 3 Series 4.10 & Down Carrier~Dana 60; Reverse Rotation; 3.73 Ratio; Reverse Rotation

Dana 60; High Performance Replacement; 5.38 Gear Ratio; Thick Dana 60; High Performance Replacement; 5.38 Gear Ratio; Thick

For Ford 8.8" (10 Bolt); 3.55 Ratio

Dana 60; 7.17 Ratio Dana 60; 7.17 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 7.17 Ratio; Fits 4 Series Carrier

For Ford 8.8" IFS; Performance Ring and Pinion; 3.55 Ratio

Dana 60/Reverse; 4.11 Ratio Dana 60 Front; Reverse Rotation; Ring and Pinion Set; 4.11 Ratio; Fits 3 Series 4.10 & Down Carrier~Dana 60; Reverse Rotation; 4.11 Ratio

Dana 60/Reverse; 4.88 Ratio; Thin; Fits 4.56 Case Dana 60 Front; Reverse Rotation; Ring and Pinion Set; 4.88 Ratio; Fits 4 Series 4.56 & Up Carrier~Dana 60; Reverse Rotation; 4.88 Ratio; Thin; Fits 4.56 Case

Dana 60/Irregular Cover; 3.73 Ratio Dana 60; 3.73 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 3.73 Ratio; Fits 3 Series Carrier

Bolts Not Included with 6.17 Gear Ratio with Dana 60 Axle

Dana 60/Irregular Cover; 3.54 Ratio Dana 60; 3.54 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 3.54 Ratio; Fits 3 Series Carrier

For Ford 9.75" (12 Bolt); 4.56 Ratio; 1997-1999.5 Models Require Additional Spacer For Pinion Bearing Preload

9.75 in. 12 Bolt; 3.31 Ratio Ford 9.75 in.; 3.31 Ratio

Dana 60/Reverse; 3.54 Ratio Dana 60 Front; Reverse Rotation; Ring and Pinion Set; 3.54 Ratio; Fits 3 Series 4.10 & Down Carrier~Dana 60; Reverse Rotation; 3.54 Ratio

Dana 60/Reverse; Oversize; Reverse Rotation; 35 Spline; 5.38 Ratio Dana 60 Front; Reverse Rotation; Ring and Pinion Set; 5.38 Ratio; Aftermarket 35 Spline Pinion; Fits 4 Series 4.56 & Up Carrier~Dana 60; Reverse Rotation; Oversize; Reverse Rotation; 35 Spline; 5.38 Ratio

For Dana 60; 4.56 Ratio; Pro Gear; Requires a 4.56 and Numerically Higher Ratio Carrier

For Dana 60; 5.38 Ratio; Pro Gear; Requires a 4.56 and Numerically Higher Ratio Carrier

For Dana 60; 4.10 Ratio; Thin Ring Gear; Pro Gear; Requires a 4.56 and Numerically Higher Ratio Carrier

For Dana 60; 4.88 Ratio; Pro Gear; Requires a 4.56 and Numerically Higher Ratio Carrier

For Dana 60; 6.17 Ratio; Pro Gear; Requires a 4.56 and Numerically Higher Ratio Carrier

with Thick Gear with 4.10 Gear Ratio and Down Carriers with 4.88 Gear Ratio with Dana 60 Axle

8.8 In. Ring Gear w/4.88 Axle Ratio

10.25 In. Ring Gear Sell Until Depleted w/3.73 Axle Ratio

For Dana 44 and Ford 8.8" - Ring and Pinions Including Timken Bearing Kits; 4.56 Ratio; Fits 3.92 and Higher Carrier Front

For Dana 44 and Ford 8.8" - Ring and Pinions Including Timken Bearing Kits; 4.09 Ratio; Fits 3.92 and Higher Carrier Front

Bolts Not Included with 5.86 Gear Ratio with Dana 60 Axle

For Dana 44 and Ford 8.8" - Ring and Pinions Including Timken Bearing Kits; 4.88 Ratio; Fits 3.92 and Higher Carrier Front

with 5.13 Gear Ratio with Dana 60 Axle with Thick Gear

For Dana 44 and Ford 8.8" - Ring and Pinions Including Timken Bearing Kits; 5.13 Ratio; Fits 3.92 and Higher Carrier Front

Dana 60; 4.09 Ratio Dana 60; 4.09 Ratio~Dana 60; Standard Rotation; Ring and Pinion Set; 4.09 Ratio; Fits 3 Series Carrier