Honda CR-V Disc Brake Caliper Replacement

2002-2004 Honda CR-V Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B1449

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$50.76 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 17cl15vn, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.248, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2005-2006 Honda CR-V Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.40555

$52.10 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B1461

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$56.53 View part →

Installation Hardware Included with Metal Piston Except Japan Built Supplied with Mounting Bracket

$59.68 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 5728, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.245, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2012-2016 Honda CR-V Disc Brake Caliper - Front Left (Raybestos)

Partslink #: FRC12731C

$57.72 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B2662

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$63.10 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Left (Raybestos)

Partslink #: FRC10285

$57.84 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 5728, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.245, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2002-2004 Honda CR-V Disc Brake Caliper - Front Right (Raybestos)

Partslink #: FRC11517

$63.29 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.25, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 108m4, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.31, Mounting Hole Thread Diameter: 0.31, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.5, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2002-2004 Honda CR-V Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B2663

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$62.62 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-1448

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$63.66 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-00923A

Supplied w/ Mounting Bracket

$64.55 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.25, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 108m5, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.31, Mounting Hole Thread Diameter: 0.31, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.5, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

1997-2001 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-00923B

Supplied w/ Mounting Bracket

$64.55 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-1449

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$64.71 View part →

2017-2024 Honda CR-V Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.40135

$65.19 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.40100

$65.79 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.40099

$65.79 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 2, Bleeder Thread Size: M10x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 10cl 15sn, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Mounting Hole Thread size: M10x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.498, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2005-2006 Honda CR-V Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.40556

$66.79 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B2910

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$65.80 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.40064

$66.86 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 2, Bleeder Thread Size: M10x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 10cl 15sn, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Mounting Hole Thread size: M10x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.498, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2005-2006 Honda CR-V Disc Brake Caliper - Front Right (Raybestos)

Partslink #: FRC11677

$66.54 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B2911

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$67.41 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.40063

$66.86 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 2, Bleeder Thread Size: M10x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 100, Larger Hole Than 1701690, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Mounting Hole Thread size: M10x1.25, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.498, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2002-2004 Honda CR-V Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.40510

$67.65 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 5735, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.243, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2007-2016 Honda CR-V Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B6887

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$67.45 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B2917

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$69.01 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.40509

$67.65 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-00946B

Supplied w/ Mounting Bracket

$69.34 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Right (Centric)

Partslink #: 142.40509

$67.75 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 5735, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.243, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2007-2016 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-00949A

Supplied w/ Mounting Bracket

$70.21 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B2916

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$69.01 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P00923A

Supplied w/ Mounting Bracket

$70.63 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-00946A

Supplied w/ Mounting Bracket

$69.34 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Left (Raybestos)

Partslink #: RC10285

$70.71 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 2, Bleeder Thread Size: M10x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 100, Larger Hole Than 1701690, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Mounting Hole Thread size: M10x1.25, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.498, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2007-2016 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-00949B

Supplied w/ Mounting Bracket

$70.21 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B6886

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$70.93 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P00923B

Supplied w/ Mounting Bracket

$70.63 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Rear Left (Raybestos)

Partslink #: FRC11852

$71.30 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Right (Raybestos)

Partslink #: RC10286

$70.71 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P00946B

Supplied w/ Mounting Bracket

$71.37 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Rear Right (Raybestos)

Partslink #: FRC11851

$71.30 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01007B

Supplied w/ Mounting Bracket

$71.41 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P00946A

Supplied w/ Mounting Bracket

$71.37 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01028B

Supplied w/ Mounting Bracket

$71.58 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01007A

Supplied w/ Mounting Bracket

$71.41 View part →

2008-2016 Honda CR-V Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.40566

$72.12 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 10cl 15sn, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.498, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2007-2016 Honda CR-V Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01028A

Supplied w/ Mounting Bracket

$71.58 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B2911A

Installation Hardware Included with Metal Piston Except Japan Built Supplied with Mounting Bracket

$72.50 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Rear Right (Raybestos)

Partslink #: FRC11851C

$71.89 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P01007B

Supplied w/ Mounting Bracket

$73.36 View part →

2008-2016 Honda CR-V Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.40565

$72.12 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P01028B

Supplied w/ Mounting Bracket

$73.55 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 13clt, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.782, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2002-2004 Honda CR-V Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P01007A

Supplied w/ Mounting Bracket

$73.36 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B2958

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$75.34 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P01028A

Supplied w/ Mounting Bracket

$73.55 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Left (WBR)

Partslink #: W0133-1910053

$75.46 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P00949B

Supplied w/ Mounting Bracket

$76.32 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 13clt, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.782, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2007-2016 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P00949A

Supplied w/ Mounting Bracket

$76.32 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B2959

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$78.72 View part →

2007-2012 Honda CR-V Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P00961B

Supplied w/ Mounting Bracket Mfd in Japan

$79.59 View part →

2007-2012 Honda CR-V Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P00961A

Supplied w/ Mounting Bracket Mfd in Japan

$79.59 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-00947B

Supplied w/ Mounting Bracket

$82.96 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-00947A

Supplied w/ Mounting Bracket

$82.96 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.40116

$83.48 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.40115

$83.48 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-00948B

Supplied w/ Mounting Bracket

$83.69 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-00948A

Supplied w/ Mounting Bracket

$83.69 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P00948B

Supplied w/ Mounting Bracket

$84.35 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P00948A

Supplied w/ Mounting Bracket

$84.35 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-00973A

Supplied w/ Mounting Bracket

$84.89 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-00973B

Supplied w/ Mounting Bracket

$84.89 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2911

$85.23 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2910

$85.23 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.25, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 13clt, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.396, Mounting Hole Thread Diameter: 0.396, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.782, Piston Material: Steel, Piston Quantity: 2, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2007-2016 Honda CR-V Disc Brake Caliper - Front Left (Raybestos)

Partslink #: FRC11711

$85.37 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-2959

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$86.59 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Rear Left (Raybestos)

Partslink #: RC11852C

$87.19 View part →

2007-2012 Honda CR-V Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-00961A

Supplied w/ Mounting Bracket Mfd in Japan

$87.71 View part →

2007-2012 Honda CR-V Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-00961B

Supplied w/ Mounting Bracket Mfd in Japan

$87.71 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P00947A

Supplied w/ Mounting Bracket

$88.46 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P00947B

Supplied w/ Mounting Bracket

$88.46 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L1448

$91.66 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Left (Raybestos)

Partslink #: RC11662C

$90.90 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L6887

$94.36 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L1449

$91.66 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-59642

$94.78 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L6886

$94.36 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-59604

$97.05 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-59643

$94.78 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-59634

$98.77 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-59605

$97.05 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2910A

Except Japan Built

$99.05 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-59635

$98.77 View part →

2017-2024 Honda CR-V Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01046A

Supplied w/ Mounting Bracket Supplied wo/ Parking Brake Motor

$101.85 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2911A

Except Japan Built

$99.05 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2916

$103.91 View part →

2017-2024 Honda CR-V Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01046B

Supplied w/ Mounting Bracket Supplied wo/ Parking Brake Motor

$101.85 View part →

2017-2024 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-01047B

Supplied w/ Mounting Bracket

$106.90 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2917

$103.91 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Right (WBR)

Partslink #: W0133-1903731

$108.28 View part →

2017-2024 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-01047A

Supplied w/ Mounting Bracket

$106.90 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3431987

$110.59 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3395956

$110.59 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L1460

$111.23 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L1461

$111.23 View part →

2017-2024 Honda CR-V Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P01047B

Supplied w/ Mounting Bracket

$111.97 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3430470

$111.89 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3414341

$112.98 View part →

2017-2024 Honda CR-V Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P01047A

Supplied w/ Mounting Bracket

$111.97 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-59052

$116.92 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Left (WBR)

Partslink #: W0133-1903743

$112.76 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2662

$117.43 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-59053

$116.92 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-59078

$117.51 View part →

2002-2004 Honda CR-V Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2663

$117.43 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2959

$123.46 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-59079

$117.51 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3361437

$123.57 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3339591

$118.85 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3403412

$123.81 View part →

2007-2016 Honda CR-V Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2958

$123.46 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-59044

$128.19 View part →

2005-2006 Honda CR-V Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3340262

$123.57 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-59090

$134.08 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Front Left (Raybestos)

Partslink #: FRC12731N

$124.06 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-59076

$137.49 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Powder Coated, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 16cl, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: No, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14x1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.384, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2002-2004 Honda CR-V Disc Brake Caliper - Front Left (Raybestos)

Partslink #: FRC11518N

$127.92 View part →

2017-2024 Honda CR-V Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-B7488

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$154.67 View part →

1997-2001 Honda CR-V Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-59045

$128.19 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-59088

$195.99 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-59091

$134.08 View part →

2007-2012 Honda CR-V Disc Brake Caliper - Rear Right (Nissin)

Partslink #: W0133-2036471

For models made in Japan

$212.34 View part →

2007-2011 Honda CR-V Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-59077

$137.49 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.25, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Powder Coated, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 16cl, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: No, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14x1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.384, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2017-2024 Honda CR-V Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-59111

$139.39 View part →

2017-2024 Honda CR-V Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B7489

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$149.33 View part →

2012-2016 Honda CR-V Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-59089

$195.99 View part →

2007-2012 Honda CR-V Disc Brake Caliper - Rear Left (Nissin)

Partslink #: W0133-1985734

For models made in Japan

$236.22 View part →

2012-2016 Honda CR-V Rear Disc Brake Caliper - Right (Passenger) (Used OEM)

Partslink #: 536-60007R

Condition: Excellent (A)
Mileage: 97,600 miles

Sale price: $103.95

$89.95 View part →

2012-2016 Honda CR-V Rear Disc Brake Caliper - Left (Driver) (Used OEM)

Partslink #: 536-60008L

Condition: Excellent (A)
Mileage: 97,600 miles

Sale price: $103.95

$89.95 View part →

2017-2025 Honda CR-V Rear Disc Brake Caliper - Right (Passenger) (Used OEM)

Partslink #: 536-10323R

Condition: Excellent (A)
Mileage: 104,700 miles

$88.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 38,000 miles

$174.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 28,000 miles

2017-2025 Honda CR-V Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 29,000 miles

$245.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 33,000 miles

$245.95 View part →

2017-2025 Honda CR-V Front Disc Brake Caliper - Right (Passenger) (Used OEM)

Partslink #: 536-10120R

Condition: Excellent (A)
Mileage: 33,300 miles

2017-2025 Honda CR-V Front Disc Brake Caliper - Left (Driver) (Used OEM)

Partslink #: 536-10121L

Condition: Excellent (A)
Mileage: 33,300 miles

2007-2011 Honda CR-V Front Disc Brake Caliper - Right (Passenger) (Used OEM)

Partslink #: 536-59792R

Condition: Excellent (A)
Mileage: 187,600 miles

2007-2011 Honda CR-V Front Disc Brake Caliper - Left (Driver) (Used OEM)

Partslink #: 536-59793L

Condition: Excellent (A)
Mileage: 187,600 miles

2023-2025 Honda CR-V Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Partslink #: 536-11412

Condition: Excellent (A)
Mileage: 33,000 miles

$205.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper with Bracket - Front, Right (Passenger) (Used OEM)

The assembly includes the caliper bracket.

Condition: Excellent (A)
Mileage: 3,000 miles

$133.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper with Bracket - Front, Left (Driver) (Used OEM)

The assembly includes the caliper bracket.

Condition: Excellent (A)
Mileage: 19,000 miles

$149.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper with Bracket - Front, Right (Passenger) (Used OEM)

The assembly includes the caliper bracket.

Condition: Excellent (A)
Mileage: 9,000 miles

$149.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper with Bracket - Front, Left (Driver) (Used OEM)

The assembly includes the caliper bracket.

Condition: Excellent (A)
Mileage: 15,000 miles

2017-2025 Honda CR-V Disc Brake Caliper with Bracket - Front, Right (Passenger) (Used OEM)

The assembly includes the caliper bracket.

Condition: Excellent (A)
Mileage: 15,000 miles

2017-2025 Honda CR-V Disc Brake Caliper with Bracket - Front, Left (Driver) (Used OEM)

The assembly includes the caliper bracket.

Condition: Excellent (A)
Mileage: 29,000 miles

2017-2025 Honda CR-V Disc Brake Caliper with Bracket - Front, Right (Passenger) (Used OEM)

This assembly includes the caliper bracket.

Condition: Excellent (A)
Mileage: 29,000 miles

2017-2025 Honda CR-V Disc Brake Caliper with Bracket - Front, Left (Driver) (Used OEM)

The assembly includes the caliper bracket.

Condition: Excellent (A)
Mileage: 38,000 miles

$229.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper - Front (Used OEM)

Partslink #: PB-7888-0000214576

Condition: Excellent (A)
Mileage: 5,000 miles

$159.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper - Front (Used OEM)

Partslink #: PB-7888-0000214571

Condition: Excellent (A)
Mileage: 5,000 miles

$159.95 View part →

2017-2026 Honda CR-V Front Disc Brake Caliper (Used OEM)

Partslink #: PB-9052-0000675377

Condition: Excellent (A)
Mileage: 1,000 miles

$169.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper with Parking Brake Actuator - Rear, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 38,000 miles

$174.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper with Parking Brake Actuator - Rear, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 28,000 miles

2017-2025 Honda CR-V Disc Brake Caliper with Parking Brake Actuator - Rear, Left (Driver) (Used OEM)

It includes the parking brake actuator (electric motor).

Condition: Excellent (A)
Mileage: 15,000 miles

2017-2025 Honda CR-V Disc Brake Caliper with Parking Brake Actuator - Rear, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 29,000 miles

$245.95 View part →

2017-2025 Honda CR-V Disc Brake Caliper - Front (Used OEM)

Partslink #: PB-9052-0000713418

This is a front brake caliper.

Condition: Excellent (A)
Mileage: 2,000 miles

2023-2025 Honda CR-V Disc Brake Caliper Set - Front, Right (Passenger) (Used OEM)

Partslink #: 536-11411

Condition: Excellent (A)
Mileage: 33,000 miles

$205.95 View part →

2023-2025 Honda CR-V Disc Brake Caliper Set - Front, Right (Passenger) (Used OEM)

Partslink #: 536-11411

This is a set that includes both sides for the front disc brakes.

Condition: Excellent (A)
Mileage: 10,000 miles

$236.95 View part →