Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$49.35 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: C L, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.551, Mounting Hole Thread Diameter: 0.551, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.25, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-B2604

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$49.88 View part →

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-00538B

Supplied w/ Mounting Bracket

$51.97 View part →

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-00538A

Supplied w/ Mounting Bracket

$51.97 View part →

✓ In Stock

1999-2001 INFINITI I30 Disc Brake Caliper - Front Right (Raybestos)

Partslink #: FRC11152

$55.63 View part →

✓ In Stock

1999-2001 INFINITI I30 Disc Brake Caliper - Front Left (Raybestos)

Partslink #: FRC11151

$55.63 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99-00563B

Supplied w/ Mounting Bracket

$57.88 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99-00563A

Supplied w/ Mounting Bracket

$57.88 View part →

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P00538B

Supplied w/ Mounting Bracket

$58.40 View part →

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P00538A

Supplied w/ Mounting Bracket

$58.40 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 99P00563B

Supplied w/ Mounting Bracket

$61.05 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 99P00563A

Supplied w/ Mounting Bracket

$61.05 View part →

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Centric)

Partslink #: 142.42061

$68.84 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.42558

Fr 10/00

$68.95 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 34h, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Mounting Hole Thread size: M10x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.335, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

✓ In Stock

2001 INFINITI I30 Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B2856

From 10/2000 Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$71.56 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 34h, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Mounting Hole Thread size: M10x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.335, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

✓ In Stock

2001 INFINITI I30 Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B2857

From 10/2000 Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$70.30 View part →

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Cardone)

Partslink #: W0133-1623140

$72.76 View part →

✓ In Stock

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.42546

$76.84 View part →

✓ In Stock

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.42545

$76.84 View part →

✓ In Stock

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Left (Centric)

Partslink #: 142.42546

$79.29 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: No, Caliper Type: Floating, Casting Number: 51, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.315, Mounting Hole Thread Diameter: 0.315, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.335, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

✓ In Stock

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-2000

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$78.68 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Rear Left (Centric)

Partslink #: 142.42558

Fr 10/00

$79.70 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Rear Right (Centric)

Partslink #: 142.42557

Fr 10/00

$79.70 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: No, Caliper Type: Floating, Casting Number: 51, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.315, Mounting Hole Thread Diameter: 0.315, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.335, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

✓ In Stock

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-2001

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$80.43 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.42557

Fr 10/00

$83.06 View part →

✓ In Stock

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-00549B

Supplied w/ Mounting Bracket To 10/00

$86.47 View part →

✓ In Stock

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-00549A

Supplied w/ Mounting Bracket To 10/00

$86.47 View part →

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L1219

$86.72 View part →

✓ In Stock

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P00549A

Supplied w/ Mounting Bracket To 10/00

$87.53 View part →

✓ In Stock

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P00549B

Supplied w/ Mounting Bracket To 10/00

$87.53 View part →

✓ In Stock

2001 INFINITI I30 Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-00571A

Supplied w/ Mounting Bracket From 10/00

$91.10 View part →

✓ In Stock

2001 INFINITI I30 Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-00571B

Supplied w/ Mounting Bracket From 10/00

$91.10 View part →

✓ In Stock

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Right (Centric)

Partslink #: 142.42545

$93.05 View part →

✓ In Stock

2001 INFINITI I30 Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P00571B

Supplied w/ Mounting Bracket From 10/00

$97.10 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2605

$93.40 View part →

✓ In Stock

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2001

$99.48 View part →

✓ In Stock

2001 INFINITI I30 Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P00571A

Supplied w/ Mounting Bracket From 10/00

$97.10 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2604

$101.42 View part →

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L1218

$97.60 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (Cardone)

Partslink #: W0133-1616270

Production: 07/01/1999-

$102.97 View part →

✓ In Stock

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2000

$99.48 View part →

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-67057

$109.21 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (Cardone)

Partslink #: W0133-1616222

Production: 07/01/1999-

$102.97 View part →

✓ In Stock

2001 INFINITI I30 Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L2857

After 10/2000

$115.26 View part →

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-67056

$109.21 View part →

✓ In Stock

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-67641

To 9/00

$117.94 View part →

✓ In Stock

2001 INFINITI I30 Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2856

After 10/2000

$115.26 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-67085

$138.37 View part →

✓ In Stock

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-67640

To 9/00

$117.94 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Silver, Caliper Finish: Zinc Plated, Caliper Slides Included: Yes, Caliper Type: Floating, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.34, Piston Material: Steel, Piston Quantity: 1, Product Condition: New, Rust Resistant Coating: Yes

✓ In Stock

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 2C-2001

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$174.90 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Silver, Caliper Finish: Zinc Plated, Caliper Slides Included: Yes, Caliper Type: Floating, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 2.25, Piston Material: Steel, Piston Quantity: 1, Product Condition: New, Rust Resistant Coating: Yes

✓ In Stock

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Cardone)

Partslink #: 2C-1218

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$134.94 View part →

✓ In Stock

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-67084

$138.37 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: Yes, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Silver, Caliper Finish: Zinc Plated, Caliper Slides Included: Yes, Caliper Type: Floating, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Inverted Flare, Inlet Port Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.394, Mounting Hole Thread Diameter: 0.394, Pad Wear Sensor Included: Yes, Pads Included: No, Piston Diameter: 1.34, Piston Material: Steel, Piston Quantity: 1, Product Condition: New, Rust Resistant Coating: Yes

✓ In Stock

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 2C-2000

Installation Hardware Included with Metal Piston Obsolete Supplied with Mounting Bracket

$161.61 View part →

INFINITI I30 Disc Brake Caliper Replacement

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Centric)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Left (Raybestos)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (Cardone)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (Cardone)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (BBB Industries)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Left (BBB Industries)

1999-2001 INFINITI I30 Disc Brake Caliper - Front Right (Raybestos)

1999-2001 INFINITI I30 Disc Brake Caliper - Front Left (Raybestos)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (BBB Industries)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (BBB Industries)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (BBB Industries)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Left (BBB Industries)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (BBB Industries)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (BBB Industries)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Centric)

2000-2001 INFINITI I30 Disc Brake Caliper - Rear Left (Centric)

2001 INFINITI I30 Disc Brake Caliper - Rear Right (Cardone)

2001 INFINITI I30 Disc Brake Caliper - Rear Left (Cardone)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Cardone)

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Left (Centric)

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Right (Centric)

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Left (Centric)

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Right (Cardone)

2000-2001 INFINITI I30 Disc Brake Caliper - Rear Left (Centric)

2000-2001 INFINITI I30 Disc Brake Caliper - Rear Right (Centric)

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Left (Cardone)

2000-2001 INFINITI I30 Disc Brake Caliper - Rear Right (Centric)

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Left (BBB Industries)

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Right (BBB Industries)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Left (Powerstop)

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Right (BBB Industries)

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Left (BBB Industries)

2001 INFINITI I30 Disc Brake Caliper - Rear Right (BBB Industries)

2001 INFINITI I30 Disc Brake Caliper - Rear Left (BBB Industries)

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Right (Centric)

2001 INFINITI I30 Disc Brake Caliper - Rear Left (BBB Industries)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (Powerstop)

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Left (Powerstop)

2001 INFINITI I30 Disc Brake Caliper - Rear Right (BBB Industries)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (Powerstop)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Powerstop)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (Cardone)

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Right (Powerstop)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Left (Dynamic Friction)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (Cardone)

2001 INFINITI I30 Disc Brake Caliper - Rear Left (Powerstop)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Dynamic Friction)

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Left (Dynamic Friction)

2001 INFINITI I30 Disc Brake Caliper - Rear Right (Powerstop)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Left (Dynamic Friction)

1996-2000 INFINITI I30 Disc Brake Caliper - Rear Right (Dynamic Friction)

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Left (Cardone)

1996-1999 INFINITI I30 Disc Brake Caliper - Front Right (Cardone)

2000-2001 INFINITI I30 Disc Brake Caliper - Front Right (Dynamic Friction)

1996-2001 INFINITI I30 Disc Brake Caliper - Rear Right (Cardone)

What buyers are saying.

Racing Partner Videos

Disc Brake Caliper Compatibility for INFINITI I30

Available Trims

Body Types

Engine Options

Transmissions