1998-2001 Nissan Altima CV Axle Assembly - Front Right (FEQ)

Partslink #: W0133-1722783

Production: 08/01/1999-

$82.83 View part →

✓ In Stock

1993-1997 Nissan Altima CV Axle Assembly - Front Left (FEQ)

Partslink #: W0133-1722607

w/o Limited Slip Differential

$62.73 View part →

✓ In Stock

1993-1997 Nissan Altima CV Axle Assembly - Front Right (FEQ)

Partslink #: W0133-1968265

$85.72 View part →

✓ In Stock

1998-2001 Nissan Altima CV Axle Assembly - Front Left (FEQ)

Partslink #: W0133-1968559

Production: 08/01/1999-

$73.72 View part →

✓ In Stock

Production: 06/01/1997-

$100.42 View part →

✓ In Stock

1998-2001 Nissan Altima CV Axle Assembly - Front Right (EMPI)

Partslink #: W0133-1612891

Production: 08/01/1999-

$116.47 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.748, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 25.125, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Type: Splined, Inboard Spline Quantity: 27, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 27, Product Condition: New, Shaft Diameter: 1.142, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1998-2001 Nissan Altima CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-6178

$109.29 View part →

✓ In Stock

2007-2013 Nissan Altima CV Axle Assembly - Front Right (Moog)

Partslink #: 17E001R

$118.34 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.748, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 24.125, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Type: Splined, Inboard Spline Quantity: 29, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 27, Product Condition: New, Shaft Diameter: 1.142, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1993-1997 Nissan Altima CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-6054

without Locking Differential

$110.24 View part →

✓ In Stock

1998-1999 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3407887

Production: 06/01/1997-

$121.83 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.748, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 24.938, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Type: Splined, Inboard Spline Quantity: 29, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 27, Product Condition: New, Shaft Diameter: 1.142, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1998-2001 Nissan Altima CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-6179

$119.49 View part →

✓ In Stock

1993-1997 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3406758

w/o Limited Slip Differential

$123.04 View part →

✓ In Stock

2002-2004 Nissan Altima CV Axle Assembly - Front Left (Cardone)

Partslink #: W0133-2236518

$120.85 View part →

✓ In Stock

1993-1997 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3501520

$126.39 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.74, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 24.125, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Type: Splined, Inboard Spline Quantity: 31, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 27, Product Condition: New, Shaft Diameter: 0.983, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1993 Nissan Altima CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-6135

with Locking Differential

$122.88 View part →

✓ In Stock

1998-1999 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3366072

Production: -07/31/1999

$130.76 View part →

✓ In Stock

1993-1997 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3406499

w/o Limited Slip Differential

$123.04 View part →

✓ In Stock

2013-2018 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-4408900

$131.16 View part →

✓ In Stock

1998-1999 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3406840

Production: 06/01/1997-

$125.71 View part →

✓ In Stock

2007-2012 Nissan Altima CV Axle Assembly - Front Right (FEQ)

Partslink #: W0133-1937467

$135.01 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.748, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 24.688, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Type: Splined, Inboard Spline Quantity: 26, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 29, Product Condition: New, Shaft Diameter: 1.142, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2004-2006 Nissan Altima CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-6218

From 01/2004

$127.52 View part →

✓ In Stock

2007-2013 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3374079

$135.64 View part →

✓ In Stock

2004-2006 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3419050

$128.56 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.74, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 36.562, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: Yes, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 3, Inboard Joint Type: Splined, Inboard Spline Quantity: 29, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 27, Product Condition: New, Shaft Diameter: 1.102, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1993-1997 Nissan Altima CV Axle Assembly - Front Right (Cardone)

Partslink #: 66-6056

without Locking Differential

$137.73 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.748, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 25.5, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Type: Splined, Inboard Spline Quantity: 29, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 29, Product Condition: New, Shaft Diameter: 1.142, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2002-2004 Nissan Altima CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-6209

$129.91 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.748, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 36.625, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: Yes, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 3, Inboard Joint Type: Splined, Inboard Spline Quantity: 27, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 27, Product Condition: New, Shaft Diameter: 1.102, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1993-1997 Nissan Altima CV Axle Assembly - Front Right (Cardone)

Partslink #: 66-6140

without Locking Differential

$138.55 View part →

✓ In Stock

2002-2006 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3352576

$131.05 View part →

✓ In Stock

2002-2006 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3401013

$149.65 View part →

ABS Tone Ring Included: No, Axle Nut Included: Yes, Axle Nut Length: 0.933, Axle Nut Socket Size: 1.26, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 5, Compressed Length: 38.687, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: Yes, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Type: Splined, Inboard Spline Quantity: 24, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 29, Product Condition: New, Shaft Diameter: 1.102, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2007-2011 Nissan Altima CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-6308

$137.61 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.748, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 37.438, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: Yes, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 3, Inboard Joint Type: Splined, Inboard Spline Quantity: 27, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 27, Product Condition: New, Shaft Diameter: 1.142, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

1998-2001 Nissan Altima CV Axle Assembly - Front Right (Cardone)

Partslink #: 66-6170

$151.53 View part →

✓ In Stock

2007-2013 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3437710

$141.55 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.748, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 4, Compressed Length: 38.438, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: Yes, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 3, Inboard Joint Type: Splined, Inboard Spline Quantity: 29, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 29, Product Condition: New, Shaft Diameter: 1.142, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2002-2004 Nissan Altima CV Axle Assembly - Front Right (Cardone)

Partslink #: 66-6211

$151.53 View part →

✓ In Stock

2013-2018 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3755148

$144.52 View part →

ABS Tone Ring Included: No, Axle Nut Included: Yes, Axle Nut Length: 0.5, Axle Nut Socket Size: 1.26, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 5, Compressed Length: 25.438, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Type: Splined, Inboard Spline Quantity: 24, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 29, Product Condition: New, Shaft Diameter: 1.102, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2007-2011 Nissan Altima CV Axle Assembly - Front Right (Cardone)

Partslink #: 66-6307

$154.20 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.933, Axle Nut Socket Size: 1.26, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 24.563, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: No, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Type: Splined, Inboard Spline Quantity: 29, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 27, Product Condition: New, Shaft Diameter: 1.102, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2002-2006 Nissan Altima CV Axle Assembly - Front Left (Cardone)

Partslink #: 66-6132

$145.75 View part →

✓ In Stock

2007-2011 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3407429

$157.65 View part →

✓ In Stock

2007-2012 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3493500

$151.93 View part →

✓ In Stock

2007-2012 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3368377

$161.13 View part →

✓ In Stock

2019-2022 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-4526301

$155.93 View part →

✓ In Stock

2002-2004 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3437191

Production: -12/31/2003

$161.51 View part →

✓ In Stock

2013-2015 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-4096443

$156.63 View part →

✓ In Stock

2019-2022 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-4526287

$164.10 View part →

✓ In Stock

2007-2011 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3453301

$157.65 View part →

✓ In Stock

2002-2006 Nissan Altima CV Axle Assembly - Front Right (Cardone)

Partslink #: W0133-2231041

$169.79 View part →

✓ In Stock

2004-2006 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3384345

$161.51 View part →

✓ In Stock

2007-2012 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3377633

$177.21 View part →

✓ In Stock

2007-2012 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3894877

$163.52 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.748, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M22x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 5, Compressed Length: 38.562, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: Yes, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 3, Inboard Joint Type: Splined, Inboard Spline Quantity: 29, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 27, Product Condition: New, Shaft Diameter: 1.142, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2002-2006 Nissan Altima CV Axle Assembly - Front Right (Cardone)

Partslink #: 66-6130

$177.83 View part →

✓ In Stock

2007-2012 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-3350648

$177.21 View part →

✓ In Stock

1998-1999 Nissan Altima CV Axle Assembly - Front Right (CARQUEST)

Partslink #: W0133-2360881

Production: 06/01/1997-

$183.81 View part →

✓ In Stock

2019-2022 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

Partslink #: W0133-4663305

$179.22 View part →

✓ In Stock

2002-2006 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3440420

$192.54 View part →

✓ In Stock

2013-2018 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3755077

$197.60 View part →

✓ In Stock

2019-2022 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-4526340

$198.03 View part →

✓ In Stock

2004-2006 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3413814

$223.86 View part →

✓ In Stock

2007-2012 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

Partslink #: W0133-3894918

$263.25 View part →

ABS Tone Ring Included: Yes, ABS Tone Ring Tooth Quantity: 44, ABS Tone Ring Type: Toothed, Axle Nut Included: Yes, Axle Nut Length: 0.925, Axle Nut Socket Size: 1.417, Axle Nut Thread Size: M24x1.5, Axle Nut Type: Hex, Boot Color: Black, Boot Material: Neoprene, Boot Rib Quantity: 3, Compressed Length: 1003.3, Contains Electronic Components: No, CV Joints Included: Yes, Does it require SDS: No, Dynamic Damper Attached: Yes, FAA_A1: When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On., FAA_A10: Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint., FAA_A11: The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load. This Is Typically An Outboard Joint Problem., FAA_A2: The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced., FAA_A3: The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up., FAA_A4: The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint., FAA_A5: The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time., FAA_A6: No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One., FAA_A7: Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly., FAA_A8: Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications., FAA_A9: When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking., FAQ_Q1: I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?, FAQ_Q10: Can I Let The Cv Drive Axles Hang While I Am Working On The Car?, FAQ_Q11: The Wheels Wobble When I Make A Turn. What's The Problem?, FAQ_Q2: When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?, FAQ_Q3: When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?, FAQ_Q4: I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?, FAQ_Q5: I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?, FAQ_Q6: The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut. Should I Reuse It?, FAQ_Q7: The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?, FAQ_Q8: Is It Ok To Use An Impact Hammer To Install The Retaining Nut?, FAQ_Q9: When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?, Grade Type: Standard, Inboard Joint Mount Hole Quantity: 3, Inboard Joint Type: Splined, Inboard Spline Quantity: 29, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Outboard Joint Type: Splined, Outboard Spline Quantity: 27, Product Condition: New, Shaft Diameter: 1.142, Shaft Material: Steel, Slip Yoke: No, Universal Joints Included: No

✓ In Stock

2002-2006 Nissan Altima CV Axle Assembly - Front Right (Cardone)

Partslink #: 66-6134

$335.61 View part →

Nissan Altima CV Axle Assembly Replacement

1998-2001 Nissan Altima CV Axle Assembly - Front Right (FEQ)

1993-1997 Nissan Altima CV Axle Assembly - Front Left (FEQ)

1993-1997 Nissan Altima CV Axle Assembly - Front Right (FEQ)

1998-2001 Nissan Altima CV Axle Assembly - Front Left (FEQ)

2007-2011 Nissan Altima CV Axle Assembly - Front Left or Front Right (FEQ)

2007-2012 Nissan Altima CV Axle Assembly - Front Left (FEQ)

2007-2012 Nissan Altima CV Axle Assembly - Front Right (FEQ)

2007-2012 Nissan Altima CV Axle Assembly - Front Left (FEQ)

2007-2012 Nissan Altima CV Axle Assembly - Front Right (FEQ)

2007-2013 Nissan Altima CV Axle Assembly - Front Left (Moog)

2007-2011 Nissan Altima CV Axle Assembly - Front Right (FEQ)

1998-1999 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

1998-2001 Nissan Altima CV Axle Assembly - Front Right (EMPI)

1998-2001 Nissan Altima CV Axle Assembly - Front Left (Cardone)

2007-2013 Nissan Altima CV Axle Assembly - Front Right (Moog)

1993-1997 Nissan Altima CV Axle Assembly - Front Left (Cardone)

1998-1999 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

1998-2001 Nissan Altima CV Axle Assembly - Front Left (Cardone)

1993-1997 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2002-2004 Nissan Altima CV Axle Assembly - Front Left (Cardone)

1993-1997 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

1993 Nissan Altima CV Axle Assembly - Front Left (Cardone)

1998-1999 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

1993-1997 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2013-2018 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

1998-1999 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2007-2012 Nissan Altima CV Axle Assembly - Front Right (FEQ)

2004-2006 Nissan Altima CV Axle Assembly - Front Left (Cardone)

2007-2013 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2004-2006 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

1993-1997 Nissan Altima CV Axle Assembly - Front Right (Cardone)

2002-2004 Nissan Altima CV Axle Assembly - Front Left (Cardone)

1993-1997 Nissan Altima CV Axle Assembly - Front Right (Cardone)

2002-2006 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2002-2006 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2007-2011 Nissan Altima CV Axle Assembly - Front Left (Cardone)

1998-2001 Nissan Altima CV Axle Assembly - Front Right (Cardone)

2007-2013 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2002-2004 Nissan Altima CV Axle Assembly - Front Right (Cardone)

2013-2018 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2007-2011 Nissan Altima CV Axle Assembly - Front Right (Cardone)

2002-2006 Nissan Altima CV Axle Assembly - Front Left (Cardone)

2007-2011 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2007-2012 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2007-2012 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2019-2022 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2002-2004 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2013-2015 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2019-2022 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2007-2011 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2002-2006 Nissan Altima CV Axle Assembly - Front Right (Cardone)

2004-2006 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2007-2012 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2007-2012 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2002-2006 Nissan Altima CV Axle Assembly - Front Right (Cardone)

2007-2012 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

1998-1999 Nissan Altima CV Axle Assembly - Front Right (CARQUEST)

2019-2022 Nissan Altima CV Axle Assembly - Front Left (Autopart International)

2002-2006 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2013-2018 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2019-2022 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2004-2006 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2007-2012 Nissan Altima CV Axle Assembly - Front Right (Autopart International)

2002-2006 Nissan Altima CV Axle Assembly - Front Right (Cardone)

What buyers are saying.

Racing Partner Videos

CV Axle Assembly Compatibility for Nissan Altima

Available Trims

Body Types

Engine Options

Transmissions