Toyota Sequoia Disc Brake Caliper Replacement

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 14b, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.892, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B2737

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$69.25 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B2736

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$70.67 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.44232

Caliper Cast# 13WL Retrofit Front Caliper

$74.80 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Right (Centric)

Partslink #: 142.44587

$71.65 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M10x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: Inner S13we, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.482, Mounting Hole Thread Diameter: 0.482, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.784, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01653B

Supplied w/ Mounting Bracket

$77.75 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 13wl, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.477, Mounting Hole Thread Diameter: 0.477, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.784, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2001-2002 Toyota Sequoia Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-2633

Casting # S13WE Installation Hardware Included with Metal Piston

$72.29 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-2712

Casting # 13WL Installation Hardware Included with Metal Piston

$80.96 View part →

2001-2002 Toyota Sequoia Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.44115

Caliper Cast# S13WE Original Front Caliper

$74.32 View part →

2008-2019 Toyota Sequoia Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.44624

12 x 1.25mm Mounting Hole

$82.67 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Right (Centric)

Partslink #: 141.44231

Caliper Cast# 13WL Retrofit Front Caliper

$74.80 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: F14g, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.503, Mounting Hole Thread Diameter: 0.503, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.892, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P01653B

Supplied w/ Mounting Bracket

$83.53 View part →

2008-2022 Toyota Sequoia Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-3276

Installation Hardware Included with Metal Piston Supplied without Mounting Bracket

$76.98 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01651A

$85.77 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01653A

Supplied w/ Mounting Bracket

$77.75 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: 13wl, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.477, Mounting Hole Thread Diameter: 0.477, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.784, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2001-2002 Toyota Sequoia Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01623A

Casting No S13WE

$86.87 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-2713

Casting # 13WL Installation Hardware Included with Metal Piston

$79.54 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01651A

$90.49 View part →

2008-2019 Toyota Sequoia Disc Brake Caliper - Rear Right (Centric)

Partslink #: 141.44623

12 x 1.25mm Mounting Hole

$82.67 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Left (Centric)

Partslink #: 142.44232

Caliper Cast# 13WL Retrofit Front Caliper

$90.62 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P01653A

Supplied w/ Mounting Bracket

$83.53 View part →

2001-2002 Toyota Sequoia Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01623A

Casting No S13WE

$91.59 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: F14g, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.892, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01651B

$85.77 View part →

2008-2016 Toyota Sequoia Disc Brake Caliper - Rear Left (Cardone)

Partslink #: 19-B3277

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$91.91 View part →

2001-2002 Toyota Sequoia Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01623B

Casting No S13WE

$86.87 View part →

2008-2022 Toyota Sequoia Disc Brake Caliper - Rear Left (Centric)

Partslink #: 141.44688

14 x 1.5mm Mounting Hole

$93.05 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: Gr, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.009, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2001-2002 Toyota Sequoia Disc Brake Caliper - Front Right (Centric)

Partslink #: 142.44115

Caliper Cast# S13WE Original Front Caliper

$89.15 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-7343

From 08/2015 Installation Hardware Included with Metal Piston

$94.64 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: Gr, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.015, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01651B

$90.49 View part →

2008-2016 Toyota Sequoia Disc Brake Caliper - Front Left (Cardone)

Partslink #: 19-3275

Installation Hardware Included with Metal Piston

$95.35 View part →

2001-2002 Toyota Sequoia Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01623B

Casting No S13WE

$91.59 View part →

Abutment Clips Included: Yes, Anti-Rattle Spring Included: No, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: Yes, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: F14g, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Banjo, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Diameter: 0.472, Mounting Hole Thread Diameter: 0.472, Mounting Hole Thread size: M12x1.25, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 1.892, Piston Material: Steel, Piston Quantity: 1, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2016-2022 Toyota Sequoia Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P01760B

Supplied w/ Mounting Bracket Supplied w/ Parking Brake Motor

$97.01 View part →

2008-2016 Toyota Sequoia Disc Brake Caliper - Rear Right (Cardone)

Partslink #: 19-B3276

Installation Hardware Included with Metal Piston Supplied with Mounting Bracket

$92.52 View part →

Abutment Clips Included: No, Anti-Rattle Spring Included: Yes, Bleeder Screw Cap Included: No, Bleeder Screw Included: Yes, Bleeder Screw Quantity: 1, Bleeder Thread Size: M7x1.0, Bracket Included: No, Caliper Color: Gray, Caliper Finish: Oil Emulsion, Caliper Slides Included: Yes, Caliper Type: Floating, Casting Number: Gr, Contains Electronic Components: No, Disc Brake Caliper Casting Material: Cast Iron, Does it require SDS: No, Dust Boots Included: Yes, FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations., FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container., FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation., FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish., FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder., FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins., FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications., FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?, FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?, FAQ_Q3: Car Pulls To One Side During Braking. Why?, FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?, FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?, FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?, FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?, Grade Type: Regular, Inlet Fitting Type: Flare, Inlet Port Size: 0.394, Inlet Thread Size: M10x1.0, Is Item A Chemical: No, Is Or Contains A Battery: No, Is Or Contains A Bulb: No, Is Prop Sixty Five Affected: No, Is the item CARB affected: No, Mounting Bolt Included: No, Mounting Hardware Included: Yes, Mounting Hole Thread size: M14 X 1.5, Pad Wear Sensor Included: No, Pads Included: No, Piston Diameter: 2.009, Piston Material: Steel, Piston Quantity: 4, Product Condition: Remanufactured, Rust Resistant Coating: Yes

2008-2019 Toyota Sequoia Disc Brake Caliper - Front Left (Centric)

Partslink #: 141.44270

12 x 1.25mm Mounting Hole

$97.61 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Front Right (Cardone)

Partslink #: 19-7342

From 08/2015 Installation Hardware Included with Metal Piston

$93.08 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01760B

Supplied w/ Mounting Bracket

$97.83 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L3276

$93.47 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99P01700B

Supplied w/ Mounting Bracket

$98.41 View part →

Installation Hardware Included with Metal Piston

$96.81 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01699B

$104.11 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P01760A

Supplied w/ Mounting Bracket Supplied w/ Parking Brake Motor

$97.01 View part →

2008-2022 Toyota Sequoia Disc Brake Caliper - Rear Left (Dynamic Friction)

Partslink #: 331-76689

$108.33 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01760A

Supplied w/ Mounting Bracket

$97.83 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Rear Left (BBB Industries)

Partslink #: 99-01700B

Supplied w/ Mounting Bracket

$108.50 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99P01700A

Supplied w/ Mounting Bracket

$98.41 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01699B

$108.55 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Right (Powerstop)

Partslink #: L2736

$101.68 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Rear Left (Powerstop)

Partslink #: L3277

$110.30 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01699A

$104.11 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97-01755B

$111.74 View part →

2008-2022 Toyota Sequoia Disc Brake Caliper - Rear Right (Dynamic Friction)

Partslink #: 331-76688

$108.33 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Front Left (BBB Industries)

Partslink #: 97P01755B

$116.14 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Rear Right (BBB Industries)

Partslink #: 99-01700A

Supplied w/ Mounting Bracket

$108.50 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3437460

Production: 11/01/2007-

$123.36 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01699A

$108.55 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3379252

$131.81 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97-01755A

$111.74 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2712

with Caliper Casting # 13WL

$136.71 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Front Right (BBB Industries)

Partslink #: 97P01755A

$116.14 View part →

2001-2003 Toyota Sequoia Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L2632

S13WE Cast#

$141.07 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3428067

$123.36 View part →

2001-2002 Toyota Sequoia Disc Brake Caliper - Front Left (Cardone)

Partslink #: W0133-1818786

Casting #S13WE - Type A - Carrier is 199mm Wide

$143.36 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3508426

$131.81 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Rear Left (Autopart International)

Partslink #: W0133-3780759

$144.23 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2713

with Caliper Casting # 13WL

$136.71 View part →

2003-2007 Toyota Sequoia Disc Brake Caliper - Front Left (Raybestos)

Partslink #: FRC11549N

w/ Casting # 13WL

$148.13 View part →

2001-2003 Toyota Sequoia Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L2633

S13WE Cast#

$141.07 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76201

$149.64 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Rear Right (Autopart International)

Partslink #: W0133-3780734

$144.23 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3361501

Production: 11/01/2007-

$153.84 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3341072

Production: 11/01/2007-

$147.81 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L3275

$155.84 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76200

$149.64 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Left (Dynamic Friction)

Partslink #: 331-76225

M12-1.25 Mount

$158.30 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L3274

$155.84 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Left (CARQUEST)

Partslink #: W0133-1919531

Production: 11/01/2007-

$160.76 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Rear Right (CARQUEST)

Partslink #: W0133-2265426

$157.14 View part →

2008-2022 Toyota Sequoia Disc Brake Caliper - Rear Left (Cardone)

Partslink #: W0133-2254932

Production: 11/01/2007-

$161.58 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Right (Dynamic Friction)

Partslink #: 331-76224

M12-1.25 Mount

$158.30 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Rear Left (CARQUEST)

Partslink #: W0133-2267585

Production: 11/01/2007-

$167.24 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Front Right (Powerstop)

Partslink #: L7342

$158.51 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Front Left (Autopart International)

Partslink #: W0133-3780716

$169.86 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Front Right (Autopart International)

Partslink #: W0133-3780737

$170.94 View part →

2016-2022 Toyota Sequoia Disc Brake Caliper - Front Left (Powerstop)

Partslink #: L7343

$175.85 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Right (Raybestos)

Partslink #: FRC12025N

$173.61 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Left (Advics)

Partslink #: W0133-1741023

$295.91 View part →

2008-2015 Toyota Sequoia Disc Brake Caliper - Front Right (CARQUEST)

Partslink #: W0133-1919524

Production: 11/01/2007-

$178.41 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear Right (Advics)

Partslink #: W0133-1741026

$232.41 View part →

2023-2025 Toyota Sequoia Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 37,000 miles

2023-2025 Toyota Sequoia Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 28,000 miles

$133.95 View part →

2023-2025 Toyota Sequoia Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 8,000 miles

$173.95 View part →

2023-2025 Toyota Sequoia Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 26,000 miles

$139.95 View part →

2023-2025 Toyota Sequoia Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

It fits 4x4 vehicles with the 3.4L engine.

Condition: Good (B)
Mileage: 123,000 miles

$189.95 View part →

2023-2025 Toyota Sequoia Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 37,000 miles

2023-2025 Toyota Sequoia Disc Brake Caliper - Front, Right (Passenger) (Used OEM)

Condition: Excellent (A)
Mileage: 39,000 miles

$196.95 View part →

2023-2025 Toyota Sequoia Disc Brake Caliper - Front, Left (Driver) (Used OEM)

Condition: Excellent (A)
Mileage: 39,000 miles

$196.95 View part →

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear, Right (Passenger) (Used OEM)

Partslink #: 536-59185

Condition: Excellent (A)
Mileage: 71,000 miles

2001-2007 Toyota Sequoia Disc Brake Caliper - Rear, Left (Driver) (Used OEM)

Partslink #: 536-59186

Condition: Excellent (A)
Mileage: 71,000 miles