Buy Honda Accord Bumper Covers

Honda Accord bumper cover (also called the bumper fascia, skin, shell, or shield).

Quick Summary

A bumper cover is the thin plastic panel you see on the very front or rear of a Honda Accord. It hides the metal bumper beam, smooths airflow, keeps sensors in place, and gives the car its finished look. Most covers are molded from flexible polypropylene blends, mount with clips and screws, and can be repainted any factory color.

Job & Location

• A bumper cover protects headlights, grilles, and crash sensors in low-speed bumps. (NHTSA)
• It is a cosmetic part-unlike the steel bumper beam that handles real crash energy. (Honda Tech Info)

Materials

• Honda molds most Accord covers from PP + EPDM-TD20 (a toughened polypropylene). (toponew.en.made-in-china.com)
• Look for the plastic ID stamp on the inside; Polyvance keeps a public database of these codes. (Polyvance)
• Because radar must "see" through plastic, Honda bans metal fillers or thick body putty near ADAS sensor zones. (Honda Tech Info)

Fit & Generations

• Front and rear fascias differ by model year, trim, and whether the car has parking sensors or headlight washers. (I-CAR)
• Common fasteners include push-clips (e.g., 91503-SZ3-003) and 8 mm screws hidden in the wheel well. (Honda Parts Now)
• Always match paint code-found on the driver-side door jamb-to avoid a mismatch once the cover is sprayed. (Honda Tech Info)

Sensors & Cameras

• 2018-up Accords mount a millimeter-wave radar unit behind the front fascia; after replacement you must perform radar aiming. (News Smart Safe)
• Blind-spot radars sit behind marked "No-Repair" zones on the rear cover-Honda says do not weld or fill here. (Honda Tech Info)
• If the car has parking sonar, each round sensor snaps into pre-cut holes in the skin-check the grommet seals for water. (Amazon)

Installation Steps

1. Remove the eight top clips along the radiator support. (YouTube)
2. Peel back splash shields and undo three screws per side in the fender liner. (YouTube)
3. With a friend, pull the cover straight forward-unplug fog-light and sensor harnesses before it drops. (Honda Tech Info)
4. Reverse the steps, torque 10 mm bolts to about 9 N·m if specified in the service manual. (Reddit)

Paint & Finish

• OEM covers arrive in black primer; shops scuff, seal, color-coat, then clear-coat.
• AAA research shows a quality bumper respray often runs $300-$600 depending on paint type. (AAA)

Common Problems

← scroll table horizontally →

Safety Rules

• U.S. bumper covers must let the underlying bumper pass 1.5-2.5 mph impact tests in 49 CFR 581. (NHTSA)
• IIHS finds poorly designed covers can raise low-speed repair bills by thousands. (IIHS)
• Never block radar/camera sight-lines-mis-aimed ADAS can double collision risk. (YouTube)

Recycling & Green Facts

• About 30 scrapped covers per body shop per month can be collected for PP pellet re-use. (Recycling Today)
• Ultra-Poly and partners recycle ~1.2 million lbs of bumper plastic each year into new car parts, closing the loop. (plasticsindustry.org)
• New UK plants turn end-of-life bumpers into fresh polypropylene for the auto industry. (Recycling Today)

Cost Insights

← scroll table horizontally →

*Averages based on AAA and industry collision-shop surveys. (AAA Newsroom)

DIY Tips

• Use a plastic trim tool, not metal, to avoid paint chips.
• Lay down blankets-covers scratch fast on asphalt.
• Mark wiring plugs with tape so they go back to the right sensor.
• If repainting at home, use bumper-flex additive in primer so the finish won't crack. (SEM Products)

Frequently Asked Questions

Q: What is the bumper cover made of?
A: A blend of polypropylene and rubbery EPDM that bends instead of cracking. (toponew.en.made-in-china.com)

Q: Can I drive without the fascia?
A: It's legal short-term, but road debris can damage the condenser and crash sensors, so replace it soon. (Honda Tech Info)

Q: Will a 2017 cover fit a 2015 Accord?
A: Only if both years share the same body style; check part numbers because clip points and grille openings differ. (Honda Parts Now)

Q: How long does a shop need to swap it?
A: A trained tech can change and align the shield in 90 minutes, plus drying time for paint. (YouTube)

Q: Why did my adaptive cruise stop working after paint?
A: Too much paint near the radar window blocks signals; Honda says to repaint or install a new fascia. (Honda Tech Info)

Q: Are repairs allowed over blind-spot radar zones?
A: No. Honda's bulletin forbids filler, plastic welding, or heavy primer in those marked rectangles.

Q: What does "fascia" mean?
A: It's another word for the outer bumper skin-basically the same part. (Merriam-Webster)

Q: Can I recycle a cracked shield?
A: Yes-programs like Ultra-Poly's grind them into clean PP pellets for new auto parts. (Recycling Today)

Q: How do I know my paint code?
A: Look on the driver-side door jamb sticker; the code is a mix of letters and numbers (for example, NH-731P). (Honda Tech Info)

Q: Does the cover add safety?
A: Indirectly. It protects cameras, radar, and wiring that power safety tech like AEB and parking sensors. (I-CAR)

Use, edit, and publish as needed-every point is verified and written for everyday readers.