Buy Nissan Rogue Tail Light Assembly

Road-ready insight: a tail light (also called a tail lamp, rear combination lamp, or brake-light assembly) on any Nissan Rogue must: fit the correct model years, meet federal lighting rules, stay dry inside, and shine bright enough for other drivers to see you stop or turn.

Fast Facts

• Every Rogue from 2008 to 2025 uses a two-piece rear lighting system: an outer lamp in the body and, on many trims, an inner lamp on the lift-gate. (Nissan News)
• Since 2021, all trims ship with LED rear lamps that last longer and light up quicker than old halogen bulbs.
• U.S. lighting must follow FMVSS 108 rules on brightness, color, and placement.
• No open recalls exist for the lamp itself, but a past corrosion recall on under-seat connectors (could dim lamps) applies to some 2014-2016 SUVs. Use the free NHTSA VIN look-up to be sure. (Motor Safety, NHTSA)

Fitment Years

← scroll table horizontally →

Bulb Sizes

(for Gen 1-2 SUVs still using bulbs)

• Stop/Turn - 7443 dual-filament (Boslla)
• Tail/Parking - T10 wedge (inner lamp)
• Reverse - T15 wedge (lift-gate)

LED lamps in Gen 3 are sealed units; they do not use replaceable bulbs. (Nissan News)

Design Features

• 2024 refresh added a smoked lens and brighter light pipe for faster brake response. (Car and Driver, Car and Driver)
• LEDs draw less power, helping fuel economy a little. (Autobest)
• Vent holes allow vapor to escape; light fogging is normal and clears as the lamp warms. (NHTSA Static)

Common Problems

• Condensation puddles - If beads or pooling stay longer than a day, a cracked seal may be the cause. Replace or reseal. (NicoClub, NHTSA Static)
• Burned sockets (Gen 1-2) - Heat plus moisture can corrode the 7443 socket; clean with electrical contact spray and add dielectric grease. (Reddit)
• Fuse blow - Check the 10 A tail-lamp fuse in the interior panel; diagram by year is on StartMyCar. (StartMyCar)

Safety Rules

Tail lamps must shine red, be visible at 1,000 ft, and brake lights must brighten compared with running lights per FMVSS 108. (eCFR)
Failing lamps can lead to a traffic stop or crash; states may fine $25-$100 for a dark rear lamp. (Check local code.)

DIY Replacement

1. Open hatch and remove two Phillips screws on the lamp edge. (YouTube)
2. Pull straight back-clips release with a pop.
3. Twist the bulb holder, swap the bulb, or unplug the LED harness on newer models.
4. Test before reinstalling. A helper steps on the brake.
5. Re-seat lamp, tighten screws. Whole job: 10-minutes, no special tools.

Maintenance Tips

• Wash lenses with car-soap, not glass cleaner; ammonia can dull plastic.
• Keep seals clear of grit; wipe gasket with silicone spray twice a year.
• Upgrade halogen bulbs to street-legal LED retrofit only if DOT-approved and built-in resistor avoids hyper-flash. Check local law first.

Upgrade Choices

• LED retrofit bulbs for Gen 1-2 give quicker on-time; pick 6000-lumen (pair) or less to avoid glare. (The Times)
• Smoke film adds style but must still pass 1000-ft visibility.
• Sequential turn modules are plug-and-play on Gen 3; they reuse factory wiring.

Frequently Asked Questions

Q: How long do LED Rogue tail lights last?
A: The built-in diodes are rated for about 30,000 hours-often longer than the vehicle's life. (Nissan News)

Q: Why does my lamp fog up on cool mornings?
A: Tiny vents let air in; water vapor can condense on a cold lens. It should clear within 30 minutes of driving. Persistent water means a leak. (NHTSA Static)

Q: Which fuse controls the tail lights?
A: Most Rogues use a 10 A "Tail" fuse in the cabin box (slot 22 on many 2014-2020 models). Check your owner's manual or online fuse chart. (StartMyCar)

Q: Can I swap only the cracked lens?
A: No. The lens is heat-bonded; you must replace the full lamp assembly.

Q: Do I need to reset the BCM after lamp change?
A: No reset is needed. The body control module recognizes the new lamp automatically.

Q: Are aftermarket smoke lenses legal?
A: They are legal only if they still meet FMVSS 108 visibility; very dark tints can fail inspection. (eCFR)

Q: What tools do I need to change the bulb?
A: Just a #2 Phillips screwdriver and gloves to keep oil off the glass. (YouTube)

Q: What is the torque spec for the lamp screws?
A: Hand-tight-about 18 lbf-in. Overtightening can crack the housing.

Q: How do I stop "hyper-flash" after LED swap?
A: Add an inline 6-ohm resistor or buy CAN-bus error-free bulbs.

Q: Where can I find recall info?
A: Enter your 17-digit VIN on the free NHTSA site. (NHTSA)

For deeper technical details, see the official Nissan press kit and U.S. safety rules linked above.